Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi,
I'm trying to obtain as much information as possible about my usb connection with Nordic chip. I'm working on DK board with nRF840, sdk14 and usbd_msc example. My problem...
Hi,
I am using a chip labeled with "N52832 QF ABB0 1717AQ".
According to its specification, this chip should have 256kB flash. However, nRFgo Studio shows that its size...
I'm currently using matlab to perform a non-linear least squares regression to fit a line to an array of samples polled from the ADC with roughly 100 data points. Is something...
Hello,
Did anyone succesfully used meshctl from Bluez with Mesh serial example? Looking at both it seems that it should be doable but the tricky part is figuring out the...
i use ble_app_uart to send data to centrol, and i don't need the UART peripheral, so diabled uart with it: NRF_UART0->ENABLE = UART_ENABLE_ENABLE_Disabled;
but the problem...
Hello,
I am working on the project through the BLE Multi-link Example.
In the description of the BLE Multi-link Example, "The central device can have a maximum of 8 concurrent...
Hi Nordic team
I have a question about Litepoint bluetooth advanced nRF5x OTA Testing.
According to the White Paper v1.0, by using the heart rate app, it is easy to evaluate...
Hi,
I am using the ble_app_uart_c example for the ble_central of SDK 12.2.0 to send data over UART to a nrf52832 based peripheral. When following the format as suggested...
i use sdk14.2 52832 as central , have bas service and myself service it have pair process , there are one change question. When I first burned the program, the bas service...
Hi,
I'm using Noble.js on a central RPi3 for DFU updates over BLE. The process is several times slower than doing the DFU over nRF Connect on an Android phone. I believe...
I am designing a NRF52 based device. One of the component , Crystal X1, EPSON FA-128 32.0000MF10Z-AJ3 used in the reference design is not available for purchase in online...
On the included Thing52 example, the LED fires m_ioext_osc_status_change from an interrupt. Eventually, when it comes to requesting use of the TWI this comparison happens...
I've noticed that if I call app_usbd_cdc_acm_write with the length set to any multiple of 64 the data will not show up on my PC until I do another write with a value that...
Hi DevZone,
I am modifying an CAN library for nRF52840 preview DK. In my project, nRF52 preview DK is working as a SPI master and Arduino CAN Bus Shield is working as a...
Hi,
I am developing a device using the PCA10028 Dev Kit
It is configured as a BLE Central, SDK 7.2, SD 120
I am starting out with the example "ble_app_hrs_c_s120_pca10028...
