Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hello,
On T-Mobile's website [1] there are some documents relating to their certification requirements [2]. In their FAQ they state that they have minimum band requirements...
Hello, we are planning to evaluate several type of AoA algorithm, and we have ISP1907-AOA-DK kit from Insight-SiP Is there any guideline you know to get IQ data from each...
Hello, Im in the middle of a custom board bringup and I am attempting to get Bluetooth GATT server working. I have tested the bluetooth code using the nrf5340dk board files...
Hi,
I'm using nrf5340 audio dk board. I configured UART0 with the help of nrf connect fundamental course - Link and I started transmitting the data in UART. But after sometime...
Dear team,
I am trying to build my CPP project with Nordic Zephyr SDK. I am using following commands:
west build --build-dir nrf_build -b nrf52840dk_nrf52840 sample -DZEPHYR_TOOLCHAIN_VARIANT...
Hi guys,
starting to improve my throughput with an nrf52805 and S112, i know this version does not support DLE, but it's also the one with lower footprint, I will ask...
HI Nordic Team,
I am developing a firmware to interface CH101 sensor, which has a firmware loading of 2048 bytes of data over I2C.
I declared buffer size as below in device...
Hi,
As i understand from the docs, the max throughput for BLE in nrf5340 is 1.4mbps. Ideally, we would like to achieve this, however anything near to 1mbps would be great...
hello,
I would like to know which operations were performed on all chips by the `nrfjprog --recover` command.
"The nrf52833-B chip is by default enabled for read protection...
Hello everyone,
I’m new to the Nordic development ecosystem and currently working on a project to implement a temperature and humidity monitoring system using the nRF9160...
I'm currently working on a project using the nRF52840 board with the MAX30001 ECG sensor. I'm using nRF Connect SDK with VS Code version 2.6.1 to develop the project on Zephyr...
I am using nRF9160 to develop a mobile measuring device.
For this purpose I need LTE and GPS, I know it is shared so I had to implement PSM/eDRX to make it work together...
Hi
I am working with a sample project (Bluetooth: Peripheral UART) for nRF5340DK in VSCode.
So I have installed the nRF Connect extension.
When I view the currently...
\nRF5_SDK_17.1.0_ddde560\examples\peripheral\pwm_driver\pca10040 In Demo1,i assigned the same pin to the 4 channels. I expect every cycle LED0 has the same behavior. But,...
