I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hi
how can i display application logs after merging application and secure_bootloader
the secure_bootloader souce I used is \examples\dfu\secure_bootloader\pca10040_uart_debug...
HI,
I am a newbie with NORDIC semiconductor.
I am working with nRF52833 and working on NFC reader with PN532 using I2C interface.
I can find libraries with SPI and...
Hi,
I have a PCA10095 and a PCA10040 where they are connected via USB to PC and are not being seen. In both cases the LED next to the interface MCU is flashing rapidly;...
I'm looking at the ZBOSS for Zigbee IAS Zone example , and in the " ZB_ZCL_DECLARE ..." statements it refers to structures such as zone_attr , poll_control_attr , and pwr_cfg_attr...
For nrf52x, a pin can be dedicated for reset, and this is from my understanding how HCI works in the sample (host line to controller reset pin). However, for the nrf5340,...
I am doing ble beacon device communication. I have two device, receiver and transmitter. Receiver device height is about 2 meter. Transmitter device on the ground. The distance...
My project builds fine in versions previous to 2.0.0. However, in 2.0.0 I'm getting an undefined reference. Any ideas where to look to track this one down?
/opt/nordic/ncs...
I am in the early stages of development and would like to proceed with only non-secure partitions on the nrf9160. I'd like to not make use of TrustZone.
I notice all of...
Hi Nordic,
I want to use an Arduino USB host shield with NRF52840-DK. Since the VDD on DK is 2.5v and MAX3421 on the shield works with 3 to 3.6 volts, I have to use an external...
What is the state of the GPIO pins during programming.
Because of space restraints, in order to get the the programming signals out from under the laird module we are...
Hello,
I am using a nrf52840-dk and communicate via SPI with an external board (NUCLEO-L476RG from ST) during development. For the development itself I am using the nRF...
Hi,
When starting to learn nRF currently, is it better to start with nRF5 SDK or nRF Connect SDK? I know Nordic will not add new features to nRF5 SDK, but what if I want...
nrfjprog restarts nrf5340DK debugger
We are running a container environment in Ubuntu 20.04 on WSL2 and the USB ports are frwarded using usbipd
When trying to flash (or...
