I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Hi,
I was using nRF command line tools 10.14.0 before. i try to update to 10.15.1 but fail with below log.
Do you have any comment for us to overcome this issue? ...
Using NRF Connect for Desktop V3.9.1 for Windows. We flash custom boards with J Link EDU 9.4 version. Since update to Programmer v2.0.1 it will not detect the J Link. Any...
Hi,
ncs1.8.0\zephyr\samples\bluetooth\periodic_adv\
ncs1.8.0\zephyr\samples\bluetooth\periodic_sync\
periodic_adv and periodic_sync
how to change to use Zephyr controller...
Hi,
I have a nRF5340 with USB DFU support which uses MCUBoot for upgrades. The current build (app_version_1) on the nRF has 0x4000 as the size of the settings_storage. The...
Hi,
Developing by NCS SDK, We found it will take 20 minutes by using mcumgr(on MacBook-pro) to BLE OTA 178KB image to nRF52840 Product Board's external SPI FLASH. it success...
The following is my set up:
platform: windows 11,
editor: visual studio code with nRF connect
SDK: nRF connect SDK v1.8.0
toolchain: nRF connect SDK v1.8.0 toolchain...
Hi,
Here is my hardware.
VBAT is 3.6-4.2V, UWB_EN is Pin28.By using nrf_gpio_cfg_output( UWB_EN ) to init this IO.
Is there any problem?Because when I using nrf_gpio_pin_clear...
Hi,
my product now is base on the nrf5340, I want to set the USB's serialnumber same as the ble mac address.
when I use the nrf52840, I can set it as follows simply. ...
Dear all,
My objective is to have an external MCU send data to an nrf52840 via UART and directly send this data via BLE to another nrf52840. I started from the ble_app_uart_c...
Hi,
I am developing an ANT TX application using the nRF52832 and SoftDevice S332. Things seems to be working well ... but I need one clarification As per the ANT example...
I am running the NRF52832 (BMD-300 module) and I'm trying to talk to battery over SMBus.
SMBus is compatible with devices up to 100 KHz.
I was wondering if there was a...
Hi,
nRF5340_PS_v1.0.pdf has multiple PIDR2 values to denote engineering versions of the chip. This seems to have been removed in subsequent product specifications, and now...
Hello, I tried to use pin_change_example in SDK to catch Interrupts (at first line) but I'm missing lots of them.
How can I catch all the interrupt events without delay...
Hi all.
My product locks up after a certain amount of time. To resolve this, i need to debug it. Since it's a makefile project, i need to convert it to SES.
The project...
