Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hello,
I know this is a documented error but I'm still struggling to fully understand and fix this.
Context:
I'm trying to make my custom display driver working again...
Hi~
I'm using an nRF52 DK connected to the nRF54L05 with jumper wires for the flashing operation. I've confirmed that the DK works correctly, as it can successfully program...
hi support team,
customer is preparing to use 21540, only use gpio mode, not using spi interface,
may i ask how to deal with spi pins of 21540, float or pull up to vdd...
Hi,
I'm having trouble with the Matter Test Harness randomly failing tests and failing to commission my device. I have tried this with both my own Matter device and the...
Hello Team,
We are using custom nRF52833 with nRF21540 (PCB). we manually controlling the nRF21540 FEM using GPIO and SPI (not using the FEM driver) for testing purpose...
Hello
On my application I have noticed that when I use hardware flow control of the uart1 (not the console uart) the processor will get stuck just before the application...
I want to use a hardware encoder to implement a mouse scroll wheel. Do you provide a QEDC routine for me to quickly learn and use? Are there any specific pin requirements...
I've had problems during installation probably due to firewall/proxy/network protection, so I managed to install from command line as specified in Installing the nRF Connect...
I have a couple of questions regarding the operation of the nPM2100 when using the LDO in Ultra-Low Power (ULP) mode, both in active and hibernate states.
Active Mode...
I used the Nordic plugin in VS code to open the process very slowly, and the build is also very slow, it takes a few hours, I have reinstalled VS code, I have also re-downloaded...
When configuring the Bluetooth protocol for NRF5340-CLLA, should I use nrf5340dk/nrf5340/cpuapp/ns or nrf5340dk/nrf5340/cpunet when adding the build configuration, or do I...
When using the nrf52832 to scan and connect to a BLE central device, the first connection is successful. However, after the first connection is disconnected and I attempt...
Hi,
We’re developing a BLE-based product on the nRF54L15 (InsightSIP ISP2454-LX) using nRF Connect SDK v3.0.2 , with MCUboot enabled for DFU.
Our BLE application is based...
