Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
I've just found through some trial and error that SoftDevice (s130 at least) on the nRF51 DK handles a sequence of notifications in the following manner:
call sd_ble_gatts_hvx...
Is it possible to （central side） send scan request fill the content based on received advertise information？
We want to control scan request message based on advertise content...
I am an experienced developer but struggling to understand nRF9160. Where can I find .h files defining HW? Where can I find data sheets describing peripherals? My task is...
Dear friend
Based on sdk17.0.2, in the ble_app_hrs routine, set NRF_SDH_BLE_SERVICE_CHANGED to 1, and by observing with nrf connect app, you can see that the Android phone...
If you take a 1K variable to a local variable, the AP will drop.
Static variables do not fall off.
I think it's a stack size issue, but how do I specify the stack size...
I am trying to get an nRF52811 to do extended advertising.
I am using: nRF5_SDK_17.0.2, version 7.2.0 of s140, SEGGER Embedded Studio 4.52, Windows 10
I have stripped...
I would like to confirm the update process when using nRF5SDK160098a08e2. I am aware of the following update process ----- Startup process: -MBR checks NRF_UICR->BOOTLOADERADDR...
Hello there,
I know how to measure the current based on Nordic tutorial. However, if I connected an external accelerometer by connecting Vdd and Gnd from nordic ev kit to...
Hi,
I want to run a CoAP server with Zephyr on a Thingy:91 over NB-IoT. Now I noticed that the Thingy only gets a private IPv4 address (10.x.x.x) from my provider which...
Hi, I am working on my custom made board, and I use P09 and P10 as digital outputs. I am aware I should disable NFC by adding the preprocessor: "CONFIG_NFCT_PINS_AS_GPIOS...
Hi All:
As the topic...........
1.what is the relations between the HID descriptor and data IN/OUT buffer?
2.Is the USB generic HID receiver_Function and tansmit_Function...
When launching the nRF9160, the following error occurred: <inf> at_host: UART check failed: 12. Dropping buffer and retrying.
Under what conditions does this come out? ...
I am trying to add DFU to my project, so I merged in the code from the example in the SDK as follows:
I included the same .c files as the example project
I copied over...
Hi,
I did some measurements today on our I2C bus and see that the GND level is different some times. The most time it is not GND level (about 800mV). I checked cross talk...
