I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Greetings,
We are using nrf-sdk v1.3.0.
We would like to monitor an adc channel using either limit event monitoring or maybe LPCOMP.
I was able to find "low level" documentation...
i am using ble_app_gatts example as beacon observer ,till 10 sec after powering up device i need connectable advertise after that period ,as i switch the advertising from...
Can you do successive updates to a Notify Characteristic using sd_ble_gatts_hvs() during the same connection interval without losing data.
The question comes down to, does...
Hi! I've successfully set op an OpenThread MQTT broker using a Rasperry Pi and nrf52 dongle and I am able to publish and subscribe to and from my computer by flashing the...
Hello!
I am working on sdk v17 and ble_app_uart. I'm going to make a button function first in this project. I created 3 functions of 'push, release, and long press' using...
I am not sure whether this is an issue with the nRF53 Engineering Example or with the SEGGER software.
I don't see any errata describing the behaviour I am experiencing...
Hello,
Is there an option to add to thread ncp example a FEM support?? I do according to de guide on the page https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_tz_v4...
I am following this series of tutorial " BLE Advertising, a beginner's tutorial ", BLE Services, a beginner's tutorial .
The problem is after establish a fresh advertising...
Hello,
I got an error 8(NRF_ERROR_INVALID_STATE) while running ble_nus_c_tx_notif_enble function.
The SDK document shows that, the err_code is
"this API propagates the...
I'm evaluating using zephyr for an nRF52840 based design. I'm able to use the nrfx drivers via Kconfig options. It doesn't appear that there any other Nordic SDK libraries...
Hello developers.
I successfully ran the Mesh project with Light Switch example on nRF52840 devices. And I have 2 questions about this.
Question 1: How can I access from...
Hi.
I'd uesd RTT viewer before SES.
RTT viewer has the menu for saving logs.
I'm a new for SES. I'm recently using SES.
I can see log message on SES, but I don't know...
Hi,
I am just unable to find the FW ID for SD v7.2.0 anywhere.
I am using SDK 17 and s140 7.2.0 and am trying to create a DFU package to update both the Soft Device...
