I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi--
On dev kit PCA100056, SoftDevice s140, SDK 15.3, in project ble_app_uart_pca10056_s140, we are trying to operate the UART TX/RX characteristic with outgoing payloads...
Hi All,
I'm very new to this Bluetooth mesh technology. Currently I'm referring to client/server switch example.
Without making any changes in the firmware I compiled...
I am seing odd time strings from AT+CCLK... Like: "+CCLK: "15/02/01,00:00:08"\r\nOK\r\n"
I think it is required that AT+CCLK responds error until it has gotten network time...
Hi!
I work at Lund university and I'm preparing a upcoming course project course. The course is about prototyping and PCB design. I want to use the nrf9160 as a example...
I get FDS_SUCCESS after I do fds_write(&desc, &m_dummy_record).
But when I do rc_read = fds_record_find(FILE_ID, REC_KEY, &desc, &tok); I get an error code rc_read = FDS_ERR_NOT_FOUND;...
Hi all,
I am trying to develop an Android app to connect to a nrf52832 running the ble_app_uart example. Previously I was using the Android-nRF-UART codes as a starting...
Hello
I have nRF52840-DK and also a nRF52840 Dongle with me and i have installed SEGGER Embedded Studio with "nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71" SDK downloaded...
I'm having a frustrating time trying to enable UARTE1 to stream fast ADC results to a terminal.
I believe I have edited sdk_config.h correctly, but looking at nrf_serial...
In continue to https://devzone.nordicsemi.com/support/233777 We tested the demo for some days, it works. But last week it stoped on open socket with error -47. At the same...
HI,
I have successfully installed Wireshark and nRF Sniffer on a Windows 64-bit machine. Now I am trying to duplicate the process on a windows 32-bit machine without any...
I want to flash in dfu sample.
*nrf_dfu_flash_erase *nrf_dfu_flash_store Called nrf_dfu_flash_init (true) to execute the above function. Since true is set in the argument...
Hi,
In order to be absolutely sure, can you confirm me that the nRF9160 module can be configured with following interfaces running simultaneously, all with dedicated GPIO...
OS in development environment ：Windows7 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
Device : nRF52840
Softdevice : s140_nRF_6.1.0
SDK : nRF5_SDK_15.2.0
Hi guys, I'm facing some trouble to put my rtc working properly. I made a code based on the rtc example...
Hi, I am developing 3 devices, two of these devices should act as nodes and send data from their respective IMU sensors to the 3rd device(central device).
I have been looking...
