Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hi Sir,
In this project, we design with nRF51822-QFAA (Flash: 256KB, RAM: 16KB) and developed the application and bootloader through the nRF51-DK (pca10028). The file...
Hi Sigurd,
Thank you for your reply. I have executed the code given by you (below link) in Segger studio(V 3.50) I observed that the output or load (pin 31) which is connected...
We have the device, where 2 power supplys can be applied. One of them is external regulator with 3.3 V output. We used it for additional load in our device. Another one is...
Hi,
I referred uart example in nRF SDK 15.0.0 and tried to implement on proxy_client program by adding all files which there in example. but still i'm facing compilation...
Hello!
I'm facing some problems when I try to broadcast a message from my receptor to the transmitters, I'm using 3 nRF24L01P. I read some things about setting the same...
I have 2 PCA10056 preview development boards.
The newer one (0.11.0 2018.3) works as expected.
The older board (v0.9.0 2016.48) the built-in LED1 thru LED4 do not...
I want to use application board and connectivity board with mesh sdk in nordic chip. Is there serialization is available for mesh like using in nRF SDK15.0.0 peripheral driver...
We are developing an application on the nRF52840 kit with SDK 15.2. We are using Keil as compiler. I have started developmet my application with the example ble_app_cscs....
Hi,
I would like to try the DK in a high voltage mode. I tried switching the power source switch to either LIPO or USB (using LIPO battery and USB respectively) but in vain...
Hi, I'm new to thingy, I want to log the data received and viewed in mobile app / web app from thingy 52 development kit which contains nRF52832. Is it possible to log data...
Hello everyone,
I am in trouble because of a vlotage of current problem, I think it is most a voltage problem.
Let me explain,
I have a NRF51DK that I programmed to...
Hi,
there is no migration guide available for 15.2 , my application currently uses 14.0.
1. when will the guide be available? can use the one for 15.0 till then? will...
I have followed this posting by Hung Bui , with light_switch_proxy_server being combined with the ble_uart.
I am using: nrf52 dk, Mesh SDKv2.0.1, nrf5_sdk_15.2.0.
By commenting...
Hi,
Errata 202 limits the use of vdd as a power source to external components and I, therefore, would like to use a GPIO instead.
My question: is there a need to use a...
