Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
Hi,
I am new to the NRF boards and I want to include the cJSON library into my project code. I am going to get some data from another device using in the cJSON format and...
Hi,
I have used nRF Connect for very long time, and have just upgraded to v5.0.1. The software seems to use a sandbox tech and restores nrfutil.exe to its default version...
Hi
I want to update the ble advertising data in my program. In nrf5340 the bt_le_adv_start() command should run only once in the main program.
Is it possible to change...
Hello,
In our project we are using FLASH 2GBIT SPI/QUAD W25N02KVZEIR external flash together with nrf5340. I have made the flash definitions on v2.6.0\zephyr\boards\arm...
Hello,
I am trying to bring up a MBN52832 Bluetooth Low Energy Module supplied by Murata that uses the nRF52832 chip. The BT module is connected to the MCU(STM32F427) via...
Hi,
We are working on nrf5340 board with NS and TF-M setup and we have SDK v2.7.0
We need to have a flash partition to store the some secure data may be a size of 4KB...
The sidebar does not load, this is version v2024.7.13.
I uninstalled it and installed it again as an admin, but it still did not load.
Sometimes it loads for a split second...
I am using a custom board with a nRF52832 (inside a BMD-300 from ublox) that I can't seem to get to a lower power state. The lowest I've been able to get is 2.2mA even using...
Hi,
I'm developing an application on the nRF9160DK with custom firmware for both the nRF52840 as well as the nRF9160 on the board, using VSCode with the nRF Connect extension...
Hi,
I am working on an application with ncs 2.5.0 that is based on a combination of the central_uart example and the hci_lpuart as I'm trying to pass data around between...
Hello,
My goal is to read out UICR address 0x10001080UL from command line / MCUMGR.
How to acheive that?
I have tried and successfully compiled ran these mcumgr handler...
I am useing NCS v2.6.0. Setting "CONFIG_LOG_MODE_OVERFLOW=y", will always print "1 messages droppend" after a period of RTT printing. CONFIG_LOG_MODE_OVERFLOW =n will no longer...
nrf Toolchain: 2.7.0 nrf Connect SDK : 2.7.0 Gateway: nrF5340 Audio DK Headset: E arbud 'MOMENTUM TW 4' (Sennheiser) I try to run and test this following application " Broadcast...
