Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been using my nRF54L15-DK board since it arrived just fine, however today when I went to flash the firmware I received the following error:
-- west flash: using runner...
Dear All, I am looking to connect to WiFi enterprise AP. So far I have been able to connect to the network using the nrf/samples/wifi/shell using a command that looks like...
Setup: SEGGER and running S112 & nRF5_SDK_17.1.0
Don't want to delete all bonds, only the specific one.
Bonded with Android and Apple smart phone
Delete pairing information...
Hi there.
Does the nRF52840 require any protection on the Bluetooth Antenna Line needed to block large unwanted signals when fitted on a Modem that also incorporates GSM...
I am using the u-blox NINA-B410 in BLE Central mode to scan for nearby devices. It only detects BLE-advertising peripherals (phones running BLE advertiser mode, BLE watches...
Could you please clarify for the clock and oscillator setup, are the LFXO oscillator and LFRC RC oscillator internal oscillators on the chip? Or is an external oscillator...
In the devzone there is a list of the "Recent and unreplied" posts, but is there a way to just browse all the devzone posts? Not just the "Recent and unreplied" list.
I...
I am debugging an issue where my nRF9160 (NCS 2.7.0) rolls back to the previous firmware after a seemingly successful upgrade. I am not getting enough logs from MCUboot to...
I was in the process of evaluating a driver when I noticed I2C communication was not working as expected. I put a probe on the relevant pins and noticed the Voltage on my...
Dear Nordic Specialist,
I would like to ask about the correct usage of the power recommendation parameter in the channel sounding configuration.
In bt_le_cs_set_procedure_parameters_param...
Hi，
Recently, I encountered a problem.
I wanted to set a MAC address of type BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_NON_RESOLVABLE, with the upper two bits set to 11 as well...
Hi,
I am using nRF9151 with nRF Connect SDK 2.9.0 .
In our project we are using an external NAND flash (MT29F4G01ABAFDWB) over SPI, and it is working successfully. We...
Planning on using the npm2100 PMIC as our PMIC for an upcoming asset tracking solution. We will have an accelerometer that will determine when the main MCU (nrf54) wakes up...
Hello,
I would like to know if it is possible in a Mtter project, to activate or not the MRP messages as mentionned in Matter Core specifications ( chapter 4.12. Message...
NCS 3.02 + nRF54L15
I'm troubleshooting a potential bug. Are these blocking routines, or if not how do I monitor for successful completion of flash write? I looked the the...
