NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
I have created two application timers. If these timers expire at same time, does the timer expire handler run concurrently or timer expire handler B run after timer expire...
hi devzone
I have no idea to pair between one nrf52 dk board and other nrf52dk board, not using nrf connect app, without wiring board to board.
I understand if i do pair...
Hi,
I built the blinky app for the usb dongle nrf52840dongle_nrf52840
and managed to flash it with the programmer v3.04. and it was successful (the leds are blinking...
Hi,
I was using JLink v7.50a with nrfjprog 10.9.0 and debug were working fine on Ubuntu 20.10 using SWD pins and JLink RTT. After changing to Ubuntu 21.10 and installing...
Hi Nordic team
We work on a custom hardware (LE Audio headset) and we need to send the battery voltage of the headset to the gateway which will be a smartphone. Using nRF...
Hi,
When SW9 is set to the default 1V8 position both the programmer and virtual COMs work fine.
When I switch SW9 to the 3V position the board is no longer detected...
Hi nrf team! I have been trying to get a couple of nrf5340 audio dk's to work with the "nrf5340_audio"-example, starting fresh with a clean install of VS Code even, and installed...
Hello
In my code i have two services one is blood pressure and second one is temperature and i have used button and indication both to send blood pressure data and temperature...
We have come to understand that the nRF5340 will not support BT classic (multiple tickets confirming this). But we still have a use-case that requires both BLE Audio and BT...
Hi guys,
I'm writing firmware for the nRF52840 using Zephyr, based on the cdc_acm example, using zephyr,cdc-acm-uart. I'm trying to blast out a ton of data, and need to...
hi devzone.
I have commercial product(led light receiver) which has nRF52832 chip and is running as central mode.
I install 'nRF connect for mobile' in my android phone...
I could not find a way, where I can get the nrfx_rtc_t const *p_instance for the nrfx_rtc_init function. There is no example where it is shown where to get this struct from...
Sometimes I get random JLinkARM DLL unknown error when I reset my device. I tried different PC, debugger, supply of chip. Nothing fixed this issue.
NRF52840 REV 3
nrfjprog...
Hi Nordic
Please explain the use of signals VDD_nRF_SENSE and VSENSE_SW_OUT in the circuit.
The board version I bought is PCA10095/0.11.0/2020.50.
Thank you.
