Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
HI,
I have an error that occured during scan with shell command :
[00:02:04.392,181] <err> sdc_hci_driver: SoftDevice Controller ASSERT: 50, 5399 [00:02:04.392,211] <err...
Hello,
Our tests and the MQTT publish documentation indicate a payload size limitation of 256 bytes for MQTT publish, which we see is set with an enum in slm_at_mqtt.c....
Hi,
The nRF document describes that the maximum length for advertisement data is 1650 bytes, but extended advertisement support only 255 bytes by default
Is it possible...
Hi,
I have an nrf9160dk which is not modified in any way as far as I can tell. I am not sure exactly which hardware revision (it just says 1.0.0 on the label), but it...
I'm trying to use the LVGL module inside zephyr, however, it requires specifying the zephyr,display driver in the device tree.
The zephyr sdk contains drivers for the FT81xx...
I am doing mcuboot using stm nucleo board through nrf connect . i am using blinky application for build but i got some error .please tell as early as possible
Building...
Hi, I am using the ZBOSS NCP production ready firmware from NCS v2.0 and I have some issue with serial communication.
I am able to run my application, and I don't have any...
HI ,
I am using west tool to build and flash the example . as I have tried this example (Nordic\v1.9.1\bootloader\mcuboot\samples\zephyr\hello world) , which is not working...
The version of bootload I use is as follows:
，Finally, the file was synthesized by NRFUtil and downloaded to 52840. The system started well when it was powered on, which...
Hello all, We 're working on our custom PCB prototype. We can see current consumption according to this profile even though the flash memory was erased. Also the modem FW...
Hello all,
I have started to port the code from the nRF52dk in Segger EM, indeed, everything so far works on the NRF52 dk , so I have opened the Blinky example for the nRF52820...
Hi,
I am using an nrf52 DK and facing an issue regarding the GPIO voltage levels. The GPIO voltage is around ~2.35V when its in LOW state and slightly increases when in...
Hi,
like mentioned in the caption, i have updated the nRF Connect SDK version from 2.0.0 to 2.0.2 and noticed, that the debugging does not longer work as expected and before...
