I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
Hello,
I'm working on an application with a rather unusual/complicated setup, and I found something I cannot really understand.
For context, I'm working with two nodes...
We are using the nRF5340 for Thread communication and an Ignion BLE Antenna (NN02-101) for range testing.
During the range test, we observed an RSSI of -25 dBm at close...
Hi all,
In our project we are using two device running on NRF chipset. One has the s140 softdevice version ( NRF52833 ) and the other has s112 version ( NRF52810 ). We are...
Hi,
I need help to disable shell_uart and its commands used in UART of BLE mesh chat example as i want to configure this UART for custom protocol along with RTS signal to...
Hi Nordic:
I am currently working on Bluetooth Matter product certification and require the certification materials for the nRF54L15. While filling out the application form...
I am using a custom board with a nrf5340 chip on it with vs code and sdk/toolchain of 2.9.1 and the bmi270 sample. I am getting and issue with my bmi270 accelerometer when...
Hi,
The nRF9151 DK product page indicates that the DK includes among other documents the hardware schematics and layout files. I've purchased the DK kit, but as far as I...
I am trying to build an application on nRF Connect SDK on VS Code and I keep getting this error:
c:/ncs/toolchains/0b393f9e1b/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc...
Hi All,
I am experiencing a significant voltage drop issue with the NRF-PPK2 device after a recent firmware update. When I set the source meter output to 3000mV (3.0V) at...
Hi All,
PPK2 isn't accurately measuring currents below 20 μ A, showing 0 nA instead. This started happening after you updated your nRF Connect software, and reverting...
I am using the nRF52840, nRF5_SDK_3.2.0, using example: usbd_cdc_acm. I mofified the example so that I transmit characters from a serial port to the USB using a virtual COM...
I have tried init modbus RTU on my nRF9160 with SDK2.5.2 using max485 module but i have faced an error. This is the error: *** Booting nRF Connect SDK v2.5.2 *** [00:00:00...
Hi forum ,
pls help me for flash erase ,write and read to be successful for windbond w25q64 here i m stacked a long days if possible pls send me a sample successfull code...
