Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Hi.
I'm using nRF51822 with softdevice 8.
I started working with the uart example. and it works fine.
However, I can't get the BLE to reconnect automatically once the device...
Hello, i'm working with nrf8001 right now. I know that nrf8001 can work like Peripheral(slave) device. This is working ok. Im wondering if it is possible for nrf8001 to work...
Hello I'm trying to utilise the multiceiver mode with nRF24L01 and Arduino, the idea is that an nRF will be able to send a message and six other receivers will be able to...
When I use nRF UART of android phone A and B to scan the bluetooth device, the scan result is below:
first picture is the result of phone A, second is phone B:
first one...
Hi,
I want to use nrf51 development board as a bluetooth alarm clock using internal RTC . How can I generate timestamps to determine current date and time. Can the timer...
hi.
i want to parse the data before sending to BLE UART.
i am fetching data from RX/TX pin. and now i want to do some modification in data before sending it.
this block...
Hi, I want to send a constant carrier during production testing of a product.
First I call sd_softdevice_disable(); then I do the following:
//Restart radio
NRF_PPI...
Hello,
in our application I can see, that sometimes the nRF51822 completely resets, during a BLE transmission.
I am using S120 as peripheral. The peripheral is connected...
Hello,
I am trying to understand the basic working principle of the bootloader so i tried the DFU example in the SDK 9 it gets compiled and when i try to flash into the...
Hello,
I am using BL600A module and Nordic softdevice and SDK9.0. The system is having NUS service and TX and RX characteristic. Now I have a requirement for firmware upgrade...
Hello,
Should the application guarantee that the data sent to sd_flash_write is available until it receives the callback or will the softdevice make a copy of the data...
Do you have an example application which automatically re-bonds to an iPhone when the phone has been powered off and then powered on.
Otherwise, what changes are required...
HI,all.
i am so sorry for my silly question here, but it is Very important to me.
i am a newcomer here ,and i am a beginner for nrf52382 and nrf51422.
I heard the...
