I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
I just updated to SoftDevice 8 and now I'm getting the address 0x200023C4 in my apps error handler function. This error happens to be the start address for the ble_evt_buffer...
Hi All,
anyone was been successful in compiling and flashing SDK 7.1 Bootloader/DFU using arm-gcc on *nix machine ?
If every single hex file needs to be flashed apart...
Hi ,
During SOFTDEVICE_HANDLER_INIT function call , if I change the NRF_CLOCK_LFCLKSRC_XTAL_20_PPM macro to NRF_CLOCK_LFCLKSRC_RC_250_PPM_8000MS_CALIBRATION , what is the...
Hi,
I have troubles programming my blinky in a nRF51DK. I have S110 v8 loaded and can flash blinky with nrfStudio. Not with GDB. It seems that the flash is not erased. After...
Hi to all,
I've started a new ble_apps_lbs project from ble_app_template. I've an nRF51822 chip with S110 already programmed, I modify the settings for the target cpu, and...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi, After i flashed the firmware MEFW nRF58122 0.11.0, MCP "start discovery" button is disabled. I flashed the lower version MEFW nRF58122 0.9.0. Same issue.
There is exception...
Dear all,
I have a question on the LFCLK accuracy in the smart beacon kit, which is pca20006.
When I see the specification of LFCLK crystal 32.768kHz, this crystal has...
I'm developing a product using a module with a built-in NRF51822 and I'm experiencing a strange error:
After staying in a connection for a long time (hours to days), the...
Hi, I'm making a product with the nRF51822 chip.
I was looking at the MFi.
As you see in the picture, the condition for not taking the MFi is like this.
At the...
Hi, I've written my own ACI code for an arm cortex M3. So far, everything is working fine. However, I've noticed that if all data credits are used up and a DisconnectedEvent...
I'm using nRF51822 SoC and i want to notify the Androïd(4.3) application with the changes of the Major value due to switching the beacon mode . How to change Major value ...
Hi,
i can say that i'm familiarized with nrf51 devices from some time ago.
Using softdevice 7.1.0 and MCP 3.7.1 i was able to perform a device firmware upgrade using just...
Hey I am working on nordic nRF51822, I have a doubt.
Basically I want to use it as an iBeacon and along the iBeacon payload I also want to send some services.
Is that fundamentally...
