Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I don't know who's in charge of Dev Academy, but the nRF Connect SDK Intermediate Lesson 9 -- Bootloaderse and DFU/FOTA section looks like it was written as a back burner...
Hello, I am trying to save some sensor data based on my current state of the device. I want to log IMU data and timestamp into my external flash (MX25R64) with littlefs file...
I am using a custom board with an nRF52840. For OTA updates, I’m using SDK 17.1.0 based on the sample codes:
Bootloader : secure_bootloader
Application : A custom...
I am developing with thingy53. I would like to enable BLE function, MCUboot and littlefs file system at the same time. I am using SDK and toolchain v2.7.0 and sysbuild as...
Hello, I’m testing a circuit built with the nPM1300. When connecting or disconnecting power via USB-C, noise is generated at the circuit's button, causing unintended signals...
Hello. I'm trying to improve the permit join-handling in our project. Right now we're simply hammering the zBoss stack with bdb_start_top_level_commissioning( ZB_BDB_NETWORK_STEERING...
The samples "nrfx_gppi/fork" and "nrfx_gppi/one_to_one" are both broken and fail to compile. I have confirmed this for NCS 2.8.0 and 2.9.1 on Linux, and 2.8.0 on Windows....
I am currently developing firmware on Qorvo's DWM3001C module , which integrates the Nordic nRF52833 . I am using nRF5 SDK 17.1.0 and the SoftDevice S140 .
My base project...
Dear nordic team,
even if enabled for mcuboot via CONFIG_WATCHDOG / CONFIG_BOOT_WATCHDOG_FEED, our device performs a reset when swapping the image. More precisely: when...
Hello,
As I understand, the nRF54L15 have pins dedicated for clock functionality.
They are marked red in figure 165 ( page 796) of the preliminary datasheet, rev. 0.8...
When I build my first blinky sample, I met a error and correct it with ( https://devzone.nordicsemi.com/f/nordic-q-a/120279/update-to-ncs2-9-1-compilation-error/529668) ....
Hello,
We use NCS2.9.0 and NRF54L15-DK do the matter development, and we use template demo, just enable CONFIG_CHIP_DFU_OVER_BT_SMP in root prj.conf, then we do the ota...
Hi,
I am currently evaluating the new nRF54L15 DK development kit.
I installed VS Code v1.96.4 with nRF Connect for VS Code Extension Pack v 2024.9.5 . I am currently...
We urgently need to add support for Band 40 (B40) to our product. Our use case is very specific, and as far as we understand, the NRF91 currently does not support B40. We...
