I use a PCA10001 board as peripheral role of heart rate service and it can be discovered by control panel. But as I download the experimental program of central role of hrs...
I'm reading the source for the nRF Toolbox app for Android 4.3 and comparing it to the Proximity Profile spec from the Bluetooth SIG, which has this to say about path loss...
Hello,
I have downloaded the software related with the "nRF51822 Bluetooth Smart Beacon Kit" in order to modify typical iBeacon's parametres such as UUID, Major ID, Minor...
Hello,
i would like to know if the new SoftDevice 130 for the nrf51822 is compatible with the DFU OTA bootloader example provided in the SDK (nrf51822/Board/nrf6310/device_firmware_updates...
Can I get uuid of central device from peripheral device(nrf51822) ?
I want to check out which smart device is connected.
May be I can tell central is iphone4s or iphone5...
I currently use NRF5SDK v17 with S112 supporting 0-2 peripherals, ideally using data extension (4.2). No encryption is used and I don't need any 5.0 features. I now wish to...
I plan on using the nPM2100 to power the nRF54L15. I'd like to confirm any recommended practices for using the reset pin of the nPM2100.
nPM2100 PG/RESET to nRF54L15...
Hi, I'm trying to use the nRF COMP peripheral in Zephyr. My application boots and runs normally until I enable the DeviceTree overlay for the COMP. As soon as the overlay...
Hello,
What will happen if I try to change the device's TX power using the vendor-specific command SDC_HCI_OPCODE_CMD_VS_ZEPHYR_WRITE_TX_POWER while LE Power Control feature...
hi,
I use nrf54l15dk with ncs-v3.1.0， the project is based sample "central_hids"；
The purpose is I want to change console uart from "pin1.04/pin1.05<uart20>" to "pin2...
I’m developing a project on the nRF52840 that uses BLE + RTC + an SD card. It’s based on a previous project that only used BLE + RTC, and I’ve added the ability to store data...
I'm trying to use a Power Profiler Kit II with a Mac running Ventura 13.7.8. If I update the Power Profiler App to v4.3.0 or v4.3.1 the PPK II is not detected and this is...
Dear Team,
I am using NRF54L15 DK, where I have UART defined and mapped as following:
uart20_default: uart20_default {
group1 {
psels = <NRF_PSEL(UART_TX, 1 ,...
I'm struggling to obtain stable ADC readings on the nRF54L15, and I'd appreciate any suggestions. I have the ADC configured with gain = 1, internal reference, 10 bit resolution...
Hello,
I'm trying to get a TIMER triggered ADC read on P1.11 AIN4. Sample advanced_non_blocking_internal_timer sounds like what I want but it isn't NRF54L15 compatible...
I am designing a very-low-cost device based on the nRF9151 and would like a quick technical clarification.
My plan is to power the SoC and all GPIO rails from a single 3...
I'm working on a project were we require the use of a custom OOB key (not generated by the device itself) and LESC.
We have both the central and peripheral device to configure...
Hi ,
Our nRF52840 chip is drawing a high-current burst of about 1.5 seconds during the DFU upgrade. Because we have a 10 mA current limit on the battery, the system browns...
Hi
According to the errata at https://docs-be.nordicsemi.com/bundle/errata_nRF21540_Rev2/attach/nRF21540_Revision_2_Errata_v1.2.pdf?_LANG=enus, a 33k resistor is required...
