Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hello I have a few questions
In my project, the nPM1300 fuel gauge example via nrf5340dk works properly. I received information such as V - I - SOC via I2C. Currently I...
I try to use Gazell and USB HID to remote wake up my computer. But after compter turns into sleep, the callback function on the Gazell Host Device doesn't being called back...
The hardware I use is nrf52840Dongle, using nrf_dm sample for development. There are a few problems:
1. I have 8 devices, all within communication range, 4 as base stations...
Hi, I get a issue, build error if enabled PGPS in prj.conf:
CONFIG_NRF_CLOUD_PGPS =y
and OK if comment this config
for this project, I used sample/cellular/Location...
Hi,
For some reason, all of the VSCode action disappears after building the application with mcuboot using sysbuild on ncs 2.7.0. The application can only be built using...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
OK, I'm working with the nRF52832 and NCS V2.6.0, and I have two different actions I need to complete at various times with the SAADC:
Every ~ 3 seconds, I need to sample...
Hi,
I'm running some transceiver tests to look at extended broadcast and ISO transfer modes. I am using nrf5340_audio_dk and ncs V2.6.0 to run nrf5340_audio application...
When i try to run or debug the ble app uart example on our own hardware using the nrf52810 there is a fatal error when executing the code.
The example does run on the...
Hello
I am using nrf5340 raytak board which does not use DC_DC power, uses internal quartz. When I play the Bluetooth peripheral example I get the following error(I using...
I'm trying to build a simple water leak detection system. The sensor would need to alert a user through SMS/mobile notification when a leak is detected.
I was thinking of...
hi, I am working on to combine USBD CLI and RTT to USB HID with SDK 17.10, configuration as below
pls see below mainloop:
other codes are based on example of USBD...
This is driving me totally nuts. There are inconsistent pieces of information in documents and code. I am getting a modem reset loop problem. The documentation says the timer...
Hi,
Long story short, I made some boards using nrf9160 modules, received parts from DigiKey, soldered but can't make them work, at all.
nReset pin is stuck low. Tried...
