Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
hello. Is the nrf5340 network core supported DFU with Single Slot? Not Dual Slot. If it is supported , can you tell me the URL describes how to DFU with Single Slot.
Hi,
I am trying to get the MQTT publisher example working on my nrf7002DK board. For this, i have done the following things
- SDK version: 2.6.1
- Board selected: nrf7002dk_nrf5340_cpuapp...
1. What is the antenna output of the DECT NR+? Is it the same pin as CAT-M/NBIoT antenna output? (i.e. pin 35) 2. In Section 8.3 of OPS document about DECT NR+, it mentioned...
Hi,
I am having similar error as reported in Case ID: 308488, however here issue is running z-test on provided Nordic test samples.
(note: nRF-connect SDK, works as expected...
Hi, I have a question about SDK. Why not a single example build out of the box in SDK. As a beginner to learn about nRF devices, if i have to face all these weird issues in...
I would like to monitor the states of switches sw0 and sw1 on my nrf7002dk board using GPIOTE interrupts.
Initially this is just for example purposes.
I eventually need...
sdk: 2.5.1
cpu: nrf5340
I have a bootloader which have a big ram block for upgrade purpose (around 250kb) in bss section (I will move it in noinit, but it is not the point...
Hi,
I am using nrf52840. we have already used 3 SPI instance (SPIM1, SPIM 2, SPIM 3). wanted to use one more SPI instance i.e. SPIM 0. but if I enable this I am getting...
Hi,
TWIM does not work well with nRF5340DK as shown in the subject. The conditions are shown below. - I/O voltage is not 1.8V. The waveform is distorted around 2.5V, though...
Hi,
We are developing a device using the nRF5340 DK and need to add external Flash memory accessible via QSPI with XIP, as the available memory is insufficient due to DFU...
Hi all,
I am very new to the nRF controller. Previously, I have worked with STM32 controllers.
Currently, I am working on a project with the nRF5340. I am having difficulty...
Hello,
In the past, i have posted a ticket to ask can the CIS and BIS modes work simultaneously. The answer is that it is feasible in the future.
Can CIS and BIS modes...
Development Software: Segger Embedded Studio, nRF5_SDK_17.0.2_d674dde
Project consists of an nRF52DK-based peripheral (remote control) and a custom nRF52832-based central...
