We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I'm developing battery powered Zigbee End Device on SDK 4.2.0. I need to be able to receive commands from Zigbee Coordinator so I'm using SYSTEM ON sleep mode.
Right now...
Hi,
I'm using nRF9160 SLM application SDK 1.9.1
We are using the GPS in 4 operation modes and in between we sent nRF to sleep, it seems when we sent it to sleep all...
Hello,
I do not see a SWO (Single Wire Output) pin on this package. The regular size package has this function on P0.18 but not on the WLCSP package.
Please advise.
...
Hi,
I have several devices with the RIGADO BMDWare on them but whose hardware is inaccessible. I want to initialize these nRF52832 chips with out nRF Bootloader, Softdevice...
hi
I use nrf52840 with SDK17.1.
1.How to DFU via ble combined uart in the same application?I have sdudied a few of tickets ,example https://devzone.nordicsemi.com/f/nordic...
Hi all:
We are developing mesh project using nrf52833 based on mesh sdk 5.0. First the nrf52833 device can be sucessfully provisioned into a mesh node using mesh lpn example...
Hi, I am a beginner developer who is developing a product using nrf52832(s131). An issue arises and asks a question.
I hope to do infinite scanning and advertising, whether...
Hi，
On the nRF5_SDK_for_Zigbee_v3.2.0 version, it is found that when the device loses contact with the parent node, the node becomes a factory new device; if you want to...
Hi,
I was creating a struct called ch201_device. So below is the code initialization.
and in the c code, I create a function for that use a method from ch201_device...
The chip I am using is the nRF24L01.
Not the nRF24L01 P .
One module is Rx-receiver and two modules are Tx-transmitter.
The test is carried out with one Rx module and...
hello,everyone! I'm having a major problem with my nrf9160 dk board suddenly not connecting to the cloud. I registered and renewed my certificate, but the result still failed...
Hi:
There is no driver on win7 using nRF5_SDK_17.1.0_ddde560\examples\peripheral\usbd_ble_uart example.
I tried to use nRF5_SDK_17.1.0_ddde560\examples\usb_drivers, but...
Hi,
I am develloping a solution with an extended advertising.
In order to see the advertising, I am using either the nrf connect mobile APP, either Nrf Connect Desktop...
Dear Support Team，
Based on SDK15.3, nRF52832, follow the instructions to run the DFU process, use the mergehex.exe tool to merge settings, app, boot, and sd into one hex...
