Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
I know that I can memory-map external flash using XIP in the NRF52 and NRF53. However, with XIP, you can't write to the memory-mapped addresses (makes sense since you don...
Hi,
I have written a code for the motor driver and that is going to be flashed onto nRF5340. There are two communication buses that I am using in the code: UART and GPIO...
Hello Nordic,
we want to use the nrf9160 to measure some stuff and send data to a server while being battery powered. Therefore we need the lowest power consumption possible...
hi is there any existing frameworks for the nrf52 avoiding zephyr. (eg using common native cmsis / freertos / lwip stacks)?
ideally looking for free (non keil) based SD...
Hi,
Whenever I try to run the NUS example at 115200 baudrate there is an error. Either it triggers an assert or I receive corrupted data.
What should be the ideal baud...
Hi,
Trying to understand the NFC example code in the nRF52 SDK. Just wondering why the source code is not provided for the NFC. Why is this developned in the form of static...
I'm looking into the power consumption of our code, and have reached the point where it looks like our application isn't going into sleep mode properly, and is using several...
I'm developing battery powered Zigbee End Device on SDK 4.2.0. I need to be able to receive commands from Zigbee Coordinator so I'm using SYSTEM ON sleep mode.
Right now...
Hi,
I'm using nRF9160 SLM application SDK 1.9.1
We are using the GPS in 4 operation modes and in between we sent nRF to sleep, it seems when we sent it to sleep all...
Hello,
I do not see a SWO (Single Wire Output) pin on this package. The regular size package has this function on P0.18 but not on the WLCSP package.
Please advise.
...
Hi,
I have several devices with the RIGADO BMDWare on them but whose hardware is inaccessible. I want to initialize these nRF52832 chips with out nRF Bootloader, Softdevice...
hi
I use nrf52840 with SDK17.1.
1.How to DFU via ble combined uart in the same application?I have sdudied a few of tickets ,example https://devzone.nordicsemi.com/f/nordic...
Hi all:
We are developing mesh project using nrf52833 based on mesh sdk 5.0. First the nrf52833 device can be sucessfully provisioned into a mesh node using mesh lpn example...
Hi, I am a beginner developer who is developing a product using nrf52832(s131). An issue arises and asks a question.
I hope to do infinite scanning and advertising, whether...
