Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Following Setup:
1.) Building light-switch-app from original https://github.com/project-chip/connectedhomeip Repo for nRF5340 from command line with nRF SDK v2.1.0
2...
Hi,
We are close to going into a certification process but before we start we need to be sure we are not missing out on your recommendations with regards to EMC performance...
Hi,
I get the error like below on the Linux XFCE 64-bit platform (Pardus 21.2 distro latest version). It works fine on Windows but having a problem on linux. How can I solve...
Dears,
Currently, when working with the nRF52833dk, I found some weird behavior.
I tried to run the blink example in nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_blinky...
Hello. I want to check "Airlog" or "hcisnoop" with nRF5340 LE audio EVK. The current development environment is VS Code. I also have a USB Dongle, but I don't think I can...
Hi,
I'm using nrf52840 with softdevice s140_nrf52_7.2.0 and I'm adding new characteristics to the ble_nus service. I've added the new handles for the new characteristics...
It appears that after a few seconds and sometimes after a few minutes sleeping threads do not wake up, even though the UART shell and BT NUS are working. The only service...
Hi,
I am trying to configure GPIOs with a custom DTS file, for initial bring-up and testing of the PCBA prior to higher-level development. During compile, I am getting a...
Hi, we have a use case where the central might need to re-bond with our peripheral (e.g., after choosing "Forget this device" in phone settings). I have learned that setting...
Hi
i am working on the nrf5340_dk for making as a controller through the hci_uart build.
can i know the gpio connection mapping on the board?
regards,
Achyuth
Hi, I'm currently having a problem with the uart peripheral.
I have an STM32 MCU connected to the NRF52840. In this case, the NRF acts only as a "transceiver".
Whenever...
I have my own code for handling pin interrupts using the NRF_GPIOTE EVENTS_PORT interrupt. I had some issues with this years ago when I was using the nRF52832 chip, which...
Hi,
is it possible to configure the hci_uart example from NCS in a way that the FICR device address of a nRF52840 is used as public device address? I cloned and compiled...
Hello,
We are trying to get the NVS example on our nrf9160 DK running. The build and the flash process looks fine but the application won't boot. Not even the typical...
Hi,
I bought a second nrf52833-dk. After I program my code on it, I can't debug or read the code because read protection is on. This is strange, because I didn't program...
