Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi all.
After finishing some test I want to generate the binary for the MCU nrf52810 using zephyr. I have look in the zephyr folder and saw the zephyr.bin file. Is that...
Hello,
I'm currently developing with a nrf52832 (QFABB0) and I have to use pins 16,38,37 and 17 as gpio.
The problem is that when I have an error for pins greater...
Hi Nordic team
Q1. According to nrf Connect SDK documentation, Zigbee and Matter samples all supported FOTA (firmware update). Where can I find the DFU samples for Zigbee...
Hi，
When the friendship node has established with the LPN node, how to verify that the friendship sends a useful message to the LPN node?Has it any API to verify the message...
Hi If I permanently see 3.3v even when the application is not running does that mean it is busted? I also see a lot of spikes in the output I have placed an order for another...
Hi.
I have a problem using dfu bootloader.
SDK : 17.1.0
SD : 7.2.0
device : nrf52840
dfu code : secure bootloader pca10056_s140_ble
uECC : 13.0.0
I implemented...
Hi Team,
I am working on NRF52832 based on the BLE mesh protocol here I am using the Light_switch example of SDK - nrf5sdkformeshv500src
Here I need to detect and monitor...
Hi,
I am using a Raytac MDBT50Q module on a custom board of mine. I have no 32kHz installed (which is available inside the module), VDD and VDDH are common and powering...
I'm porting code from my device which uses the nRF52832 to the 840 DK. My general process was to get the code developed on my own device to run on an 832 DK, then an 840 DK...
Hello everyone, I'm new here, and new to using the Nordic boards. I have a question regarding the RF connector in the nRF52840_DK. I am trying to do some RF measurements with...
Dear Team,
We notice that systemOFF current varying from 220 nA to around 500 nA for different devices. For some devices we are able to achieve 300 nA as mentioned in the...
Hi,
I'am using the ble_uart example on a custom board, where I have the issue that the BLE advertising is only available after a reset OR when I comment out the uart_init...
Hello,
I would like to implement beacon feature with a periodic (each 10s) advertisement data update.
This is an extrapolation of my code:
Is there some function that...
Hello,
The part i am using is NRF52840 Rev 2 (Build Code Dx0)
How can i exact know what revision or build code the SOC has ?
I want to determine in application what...
