Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I use nRF Connect to connect to nRF52832 device. 1st connection is bonded authenticated encrypted link, but 2nd connection becomes not bonded unencrypted link. Why 1st and...
Hi,
I was provisioning devices for a customer today when I noticed at the end of provisioning that the JSON database file that was exported had all the features except ...
Hello,
We are developing a library which is intended to use the trustzone feature available with nrf5340 DK. We followed the instructions available in Using a custom Secure...
Hi
When I use the nrfjprog with the command line:
The application is starting and the code running.
If I do the same again (with the same hex or a newer one) the...
I am developing a project with nrf mesh SDK 5.0.0, I use dimming code, but the code uses rtt input, if I want to replace rtt with buttons, what should I do? I'm learning,...
Hello! I will try to make this as simple as possible with the details regarding this issue What I have
nRF52840 DK (pca10056) (As BLE sniffer)
nRF52 (pca10040) (Used...
Hello
We are using NRF9160 AssetTracker 1 and MQTT to AWS. We have a AWS Certificate, Root Certificate and Public and Private Keys on the device.
We want to start testing...
My device get deep sleep mode. It wakes up from reset button trigger. Because I couldn't gpio pin trigger for wakes up. So I put vibration sensor to reset pin. It wakes up...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
Hi,
I've been using the DWT macro cell successfully on the app core to provide high accuracy timing information. E.g., with these declarations:
and enabling the cycle...
hi ~
peripheral can bond how many smartphones ?
and What will happened if over bond?
i use sdk12.2 below 'is my setting
#define SEC_PARAM_BOND 1 #define SEC_PARAM_MITM...
Hi…
I am using freeRTOS V10.0.0 release
I am using nRF52820 + SDK V17.0.2 with SD112 V7.2.0 along with tickless idle as this is a battery based product…
When my application...
Hey guys, I'm an embedded software engineer and I am currently working in a prototype, specifically using the Circuitdojo Feather nRF9160 , I am also using a Hologram International...
Based on the Sample "Bluetooth Peripheral_uart:
My latest attempt to send long data stream:
I send:
1234567890123456789012345678901234567890123456789012345678901234567890...
