Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi there,
I faced this issue while I was setting up a test through two UART0 & UART1 ports on NRF5340 chip, using baudrate 1000,000.
Here is the setup:
UART0 &...
I currently use nrfConnect on android to download firmware to nrf52832s. I am just getting started with nRFUtil and the dongle.
If I understand correctly, I should be able...
I have a nRF52 DK from DigiKey that I've been evaluating and I ran into an issue: I had a custom app that was talking through Bluetooth and sharing some custom characteristics...
Hi, I'm using NXP LM75B temprature sensor based on nRF SDK's example code.
I would like to save power on this sensor.
I have prepared the code as follows:
Following...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
I'm developing for nRF52832, SDK 17.0.2 and softdevice S312 7.0.1.
After I upgraded from Segger Embedded Studio 6.22a to 6.30 I found that turning on any compiler optimisation...
HI DevTeam,
I'm using the nRF52840 as co-processor due to the semiconductor shortage and I don't need to use the RF section. What should be done with the antenna pin in...
This is the implemenatation spec for GATT server database (reader) firmware i am working on.
I have implemented advertisement packet using nRF Connect SDK latest.
Not...
Hello,
I am customizing the BLE DFU bootloader for nrf52820. Integrated an LCD to it.
Now I need to display the percentage of firmware download on the LCD. It will take...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832. I want te retrieve data from a battery cell monitor which uses the LTC6804 from Analog Device.
...
Hi,
I need to capture time in nanosecs between 2 tasks, for which I am using the zephyr suggested time measurement code as in:
When I am trying to compile the above...
Dear DevZone,
our goal is to replace the RX side of an old system, which is using the nRF2401. For real-time capabilities, the Shockburst protocol was employed.
Reading...
Hello, Nordic Engineer
I use nrf52811 and SDK 15.3.0
In example 《ble_app_uart》, I added timeslot（ESB）
Run this code《nrf_esb_write_payload(&tx_command);》
Subsequent...
STEVAL-STMDLTE WITH NRF52840 using UART
We are trying to integrate the STEVAL-STMODLTE Link chip into the NRF52840 for rapid prototyping.
Trying to interface nrf52840...
