Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi,
Currently, I'm working with the ISP2053, one of the nRF5340's 3rd models.
As a beginning, my colleague wrote a code based on the throughput sample and I found...
Hi iam using nrf52840 dk board and for programming i use keil software ,the issue is i could not program the dk board and it is a brand new board. When I try to program it...
Hi guys! I'm a beginner of nRF52832, and I met an issue as the topic said.
When I init the UART module, it will cause an "APP_UART_COMMUNICATION_ERROR", and the error code...
Note: this question was previously a reply on my other question, but I accidentally marked it as an answer so the thread got locked. I have now deleted that reply and am posting...
Dear All,
could you explain the function of TP8 and TP9 of the nRF9160 DK on HW 1.0.0 ? These test points are connected to pin 124 and 125 of the nRF9160 which are marked...
I am using nrf9160 custom board with an external flash memory mx25l6433f. I first tested the external flash with the example 'sdk-zephyr/samples/drivers/spi_flash_at45' and...
Hi,
I;m working on nrf52840 dk i have to enable ble5.0 long range.
i set the tx power 8.
according to my project my device will be always in advertising mode and my...
I am trying to scan for BLE devices in my area, but when I connect to the USB840XZ with the windows development tool the "Start Scan" button is not active. There are some...
Hi everyone,
is there a way to update the AWS certificates from certificates.h with the SDK 1.9.99? Following the AWS FOTA instructions it seems that i can update the certificates...
Hello everyone,
I am currently testing the secure bootloader over USB example but I am currently facing an issue when I start a DFU.
Here is my configuration:
...
Hi,
Application details:
I have a datalogger application that samples data every second. It uses the following modules:
TWIM0 -> To communicate with external RTC clock...
Hello,
I am working on application using nrf52810 SDK version nRF5_SDK_14.2.0_17b948a.
Here my application sends 240 bytes of data every 150 ms. But after sending few...
Hi,
I use the a gpiote_in_event to trigger a number of PWM pulses which works fine so far. However, the exact behaviour of the generated signal is important so that the...
Hello, I am using nRF52-DK with Segger Embedded Studio and I'm running the following code that first blinks the LED1 on&off 5 times, and sets up BUTTON1 for wake up, and then...
