Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello,
I've been trying to access the nRF52840 dongle through the pc-ble-driver-py library. However, I can't get the Nordic examples to run. Here's what I did so far:...
I want to send my sensor data from one node to another node using BLE mesh. my data is at about 128 bytes I am trying to create a custom model but it's hard to know how to...
Hello, I am trying to advertise twice in my project with different gap_params.
First, I have started advertising with the following conn_params (shown below)
#define MIN_CONN_INTERVAL_ADV...
In a old post https://devzone.nordicsemi.com/f/nordic-q-a/58034/uart-communication-between-nrf52840-and-nrf9160-on-nrf9160-dk This question was already answered but this solution...
I am now using nrf52840 dongle and want to develop a software to control dongle like NRF connect desktop software, such as scan devices, connect device with passkey, read...
Hi
I am interesting to generate 1,638,400 Hz is an external clock for a peripheral on one of the NRF pins.
Please advise how can I generate this clock value on one of...
To the kind attention of Nordic support team,
We have this custom board using nRF52833 powered up from usb and in high voltage mode (ldo). The problem is that we are...
VS Code (running on Ubuntu 21.10) can't find the connected nRF52840 dev kit. " Could not find any connected boards " is all that's shown under CONNECTED DEVICES. Beside that...
I'm learning to use the Asset Tracker V2 example and planning to build a POC product on top the example. The biggest issue at the moment is with power consumption. On the...
To the kind attention of Nordic support team,
We have a problem that may very well be linked to this thread
https://devzone.nordicsemi.com/f/nordic-q-a/65202/usbregstatus...
Hi, I got my border router working fine, but I do not understand its use. How can I connect (which kind of protocol?) with the nrf5340 from my laptop to send turn on a led...
Hello
We check the current in system off in PCA10059 board. and use the ble_app_template application.
If set the VDD 3.3V, after the system off, measure the current is...
Hi Team,
I want to connect power pins on the nrf52840 chip in the schematic.
I find there several VDD pins, how can I select and connect them?
Best,
Gaosheng
Hello,
we are currently developing a customer product based on the nRF9160 SIP.
The requirement is to send the battery voltage periodically over the CoAP protocol (PUT...
