Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
While connecting with one NRF Development kit and Android NRF blink app mobile code, data is getting received properly.
But with some changes in development kit code ,We...
Hi,
I am using memfault with sdk 1.6.1 and want to get the reboot reason in my code. it is shown on boot and it seems the nordic register NRF_POWER->RESETREAS is then reset...
Hello Team, Could we control the 64MHz clock for some peripherals? I know that it is controlling by the clock control system itself and no way to configure it by the user...
Hi
When I generate a Zephyr Project with SES I get all c-files from CMakeLists.txt in the SES Project tree.
But I want also the h-files in the project tree.
How can...
We have developed our own application board with the nRF9160 on it according to the reference design.
The modem is connected to an application controller by UART (no HW...
when i connect NRF9160-DK (version 0.8.5 )to the CMW500 for CAT-M test, we have send the below three commands
AT+CFUN=4 AT%XSYSTEMMODE=1,0,0,0 AT+CFUN=1 to
the NFR9160...
Hello, all.
I'm using nRF52833, pca10100.
What I'm trying to do is just manually disconnect.
So, I referred to the Multi-link Central example. Multi-link Central is...
At this link https://infocenter.nordicsemi.com/pdf/nRF52840_Rev_2_Errata_v1.4.pdf, in 193 and 198 ID，this seems to be a mutually exclusive. In 198 workaround, .synchronize...
In the AGPS sample for nRF9160 "v1.5.1\nrf\samples\nrf9160\agps" main.c, there is option to set interval an and timeout in "gps_config" structure in "gps_start_work_fn" routine...
We ran into an issue when trying to use mcuboot on nRF53 with an external QSPI flash. In hal_nordic/nrfx/drivers/src/nrfx_qspi.c, the function nrfx_qspi_write has the following...
dear all：
I want to know how many beacons can be scanned by a gateway in the application of beacons.
At present, we have only actually tested more than 100 tags that scan...
Hi, Nordic Team. I'm using BC805M EK (nRF52805). In my code, I'm using SAADC (PPI interruption), TWI, BLE and System ON/OFF button .
Q1) I don't need RTS, CTS on the UART...
Hi
How to control two channels separately with one PWM instance?
I want to turn on/off the PWM output of each channel with any interrupt process.
app_pwm_disable() and...
Hi,
I am using nRF52840 , SDK 17.0.2/ble_peripheral. I am integrating Mesh SDK 5.0.0 libraries with ble_peripheral libraries in the nRF SDK 17.0.2 as per the documentation...
