Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
hello,
I need send 10000bytes large data send central to peripheral in single transmission. I using example code ble_app_uart_c in SDK15.2 nrf52832. what are the parameter...
Hello
I am writing low-power application where NRF is called from the other chip by interrupt, performs bluetooth scan and sends data back over UART. Of course, I want to...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image.
I am using ‘ble_app_bliky” for my application development. In this “Button...
Hello =)
Im trying to run the ble_app_uart_c example on a NRF 52810 Chip.
i got:
SEGGER Embedded Studio for ARM V4.12
SDK 15.3.0
examples\ble_central\ble_app_uart_c...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image.
In ‘System OFF’ after GPIO interrupt, chip will reset and control will come...
Hi All
I am using nRF52832 with softdevice s132_nrf52.6.1.0
and I have to use both protocol (ble & gzll)
the default protocol is ble
after i keep pressing the button...
Hello,
I am working with nrf51822. I have developed a custom evaluation board. Accidently I connected voltage in reverse polarity to the device now i am unable to program...
Hi,
I am trying to understand possibilities provıded by Bluetooth Mesh Technology.
In my topology, there are tywo types node.
The first type of node is connected to...
Hii,
I am currently using two nRF52832 SDK boards to implement text message exchange with another nRF52832 SDK board via BLE Mesh SDK 2.0.1.
However, when I try to increase...
Hi. I'm using a nRF52840 chip and have a flavour of Proximity profile example being used with some custom services and characteristics that have been added. All is good in...
There is my function for writing to flash.
It works when NRF52832 start from reset, if works when the NRF52832 gets data over BLE but it does not works after "power down...
Hello, for some reason, the UUID's on a Galaxy Note 3 are messed up or are not being read properly. I have included screenshots of the issue. The note 3 is running android...
I'm trying to understand how the UARTs are configured on the nRF9160 DK.
The spec mentions that there are two UARTs, a primary and a secondary. https://infocenter.nordicsemi...
Hi Team,
I transplant the project nRF5_SDK_14.2.0_17b948a\examples\peripheral\uart to the project ble_central\ble_app_multilink_central, uart doesn't work.
It indicate...
Dear,
I am using LTE_M:
# LTE link control CONFIG_LTE_LINK_CONTROL=y CONFIG_LTE_AUTO_INIT_AND_CONNECT=n
and I want connect nRF91 DK with 2other systems (by UART)....
