Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi,
The above pins are connected to test points in the ref schematic but stated as Nordic reserved in the pin description. Should I connect them to test points or can I...
I am wondering whether it is possible to maintain backwards compatibility for BL4 while also taking advantage of the BLE5 LR CODED PHY?
I am guessing I could scan in AUTO_PHY...
Hi,
What are the reasons for the nRF connect app or the nRF Mesh app or even the nRF UART app to connect to an Android phone?
I can see the DK advertising. I can see the...
Hi,
I am using nRF52832, SDK 15. My code is based on the freeRTOS code examples.
I am trying to Run my Task Every 10 ms. I tried to test this by using a counter to print...
Hi,
I have a problem with soft device. My code build well but when i try to compile it on nrf52840, i have below error:
Then i tried to go in boot loader:
Therefore...
Hi, Everyone
I have a product (named "A") developed on sdk12.3 and 52832.
This product has peripheral function and MTU Size is 64.
If I use "nRF Toolbox -> UART" on my smartphone...
Hi,
I'm working on the Mbed-OS USB HAL implementation for the nRF52840. I'm having a bit of difficulty getting the expectations of the USB stack to match up with the event...
Hi,
I completed the getting started guide (Getting Started Assistant app) of the nRF Connect v2.6.1:
I installed the toolchain, the SEGGER Embedded Studio and opened a...
Hello I am working through my project and ran into the roadblock of the nrf52840 not being able to use the 250kbit radio mode.
I tried a few workaround and ended up getting...
Hi,
I am working on the "pin_change_init" example to develop my interrupt based function.
I have added three pins/buttons into it and out of which only are working properly...
I AM AT THE END OF MY SANITY!!!
I have tried everything. SEGGER, Keil, installed J-link like 5 times, Python, nRFgo, nRF Connect for Desktop, nRF5x Command Line Tools...
Hello,
We are using nRF52840 with SES sdk 15.0 version. My other thread is here in that got problem with nrf_cal_set_callback(calendar_updated, test_Interval); this function...
I am trying to use a sensor that needs 9600 baud rate with the nRF52840-DK. I've set the baud rate to 9600 on the sdk_config.h. Would I still be able to see the transmit/receive...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Hello
I am using Segger Embedded Studio with nrf9160. I can 'Build and Run' the 'asset_tracker' project but the LEDs are not blinking and my development kit is not connecting...
