Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
NCS 2.4.1 nRF52840
My project is a battery powered SED based on the coap_client example. It is configured to autojoin using a hard coded pksd. I see on Wireshark that my...
Hello, I want to configure the BMP390 using I2C on my custom board. However, when I try to read the CHIP_ID register, I am unable to get the default value, and the function...
Hi,
I referred to this doc for hardware setup
However, in the programmer in nRF Desktop, I got the following log:
17:37:36.199
Error: Failed with exit code 1...
Hello person in charging,
I would like to know whether there are something information on vulnerabilities in the proprietary mode of nRF51 and nRF52, respectively.
Thanks...
Hello,
After an update to the NRF connect for Desktop the Programmer application can no longer program my nRF52840 dev kit (PCA10056, 3.0.0). Trying to revert the update...
Hi,
In our project, we're using Mcumgr FS to download files from our device.
After tweaking the BLE configuration parameters using the throughput sample ( https://github...
Hi
The datasheet of the nRF9151 is missing the statement in the nRF9161 datasheet:
RF 3GPP compliancy requires 3.3 V.
Is the nRF9151 reaching compatibility down to 3V...
I have four of these devices. nRF5340 Audio DK.
I would like to use them as follows. Is there a way to set them up?
Device A: source
Device B: sink left
Device C:...
Recently, we started developing our new project using the nRF52832 as our controller.
We are using Segger Embedded Studio (5.42a) as our IDE.
My question is: Are there...
I work for nRF52833 on NCS2.8.0.
I try to set SB_CONFIG_MCUBOOT_COMPRESSED_IMAGE_SUPPORT=y for sysbuild.
build error is occured.
Maybe there is not enough RAM for mcuboot...
My NCS version is 2.6.1, and the modem firmware version is 1.3.6
I found that delta upgrade often fails when testing the firmware of FOTA upgrade modem for 9160. Currently...
Hello. How can I monitor that SoftDevice is working properly? I am trying to monitor using Radio notification, but RADIO Active does not guarantee that the SoftDevice is working...
Hi ,
I am running "Cellular IoT Fundamentals". In Lesson 4, Exercise 1, has MQTT communication. Everything went well up to the point where I have to PUBLISH from MQTT Explorer...
