I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
I am not sure if this is an issue with the nRF Connect extension or the my Thingy91 but when I use the "Flash" button in the actions tab of the NRF Connect extension to program...
I am working with SDK v2.3.0 and a custom board with nRF9160
When I wanted to start my project again after some time, the build configuration had disappeared.
And creating...
I am trying to enable the Channel Sounding feature on the nRF54L15 DK by sending HCI commands over a "USB to UART" interface. For this purpose, I created the "hci_uart" sample...
Hi,
I'm developing a Channel Sounding application on nRF54L15 and trying to understand how the different TX power settings interact.
I have a few questions:
What does...
DevZone Post: Custom nRF54L15 Board Not Recognized by Kconfig (Falls Back to Apollo4X)
Summary: I am bringing up a custom board based on the Raytac AN54L15Q (nRF54L15)....
Hello
When following the guidline of a new way to extend boards , VSCode "Add Build Configuration" is blank. Am I doing something wrong or this is not yet supported by...
HI
I’m currently using NCS 3.2.1 , working with the periodic_adv_conn sample.
On the advertiser side, after receiving data from a node during each periodic sync broadcast...
Environment
nRF9151DK.
Using nRF tools and SDK v3.1.1 & also v3.2.3.
Based in New Zealand and currently on Spark network.
Issue
Trying to run the sample app...
Good day,
We are developing a board with a nRF54L15 + nRF7002 for BLE and WiFi connectivity.
The Nordic nRF54L15 + nRF7002 reference design has been a good starting point...
I see this errata: https://docs.nordicsemi.com/bundle/errata_nRF54L15_Rev2/page/ERR/nRF54L15/Rev2/latest/anomaly_L15_24.html#anomaly_L15_24
It says this:
"Symptoms ...
Hi, in order to be familiarized with the transceiver we have purchased an evk nRF9151 from Nordic.
I have some questions because an issue appears when I try to modulate...
hi guys,
I am using the nRF54L15 for software development. I have a requirement to define a space in the chip's internal flash for data storage. I referred to the soc-flash...
I have been experience that the if the device under a DFU process reports the error BUSY, because the external flash on the device is used for fileaccess the DFU process from...
