I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
I followed Lesson 1, exercises 1 and 2 of https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/ and successfully built and flashed the blinky sample on a nRF54L15...
Hi,
I'm porting a working SPI camera demo from nRF52840 to nRF54L15 and I'm stuck with an issue where the SPIS RX amount is correct, but the received buffer is all zeros...
I have worked a bit with ESB and see that there are functions to get/set a channel, as well as check the RSSI value in the "struct esb_payload" for a packet. Are there already...
Hi, I am using NCS v2.9.0.
I am using sysbuild to build MCUboot and application images. Following are relevant Kconfig options:
mcuboot.conf
CONFIG_MAIN_STACK_SIZE...
Hi, having a little of an issue and would appreciate your support:
When bringing up a board which has the nRF9131 and the nPM6000 I'm getting the following error when doing...
Hello,
Currently working with NCS v3.10 and using SMP service with external flash to store image in a custom board. I'm capable of upload zipped application using DFU button...
I am using the nRF9151 DK, using the Serial LTE Modem firmware from the nRF Connect quick start.
I am planning to use nRF9151 as a serial modem, and connect it to my Host...
Hello
I was attempting to update a pre-production project where we have 2 servers connected to one gateway where the servers send the audio data back to the gateway with...
Hey guys, I want to store sensor data as circular buffer in non volatile memory. I saw https://docs.nordicsemi.com/bundle/zephyr-apis-latest/page/group_file_system_storage...
If a heartbeat or other chunk reliant on symbol file data is ingested when there is no symbol file associated with the Software Version / buildID it seems like the chunk is...
Hello,
I am currently trying to make an application that can do FOTA and store the secondary firmware image on an external flash using sQSPI. The project I started is based...
Hello,
We use the nrfx spis driver for communication between a ST processor (master) and a Fanstel BT840 module (nRF52840).
We have upgraded ncs from 2.6.0 to 3.2.1 and...
I am using a GPIO pin ( P1.05 ) as a reset signal for an external CPU component. The pin functions correctly and stays low when tested in a basic GPIO application. However...
I'm using NCS 3.2.4. When USE_PARTITION_MANAGER is active, the ARM linker script defines ROM_SIZE as PM_SIZE (the full app partition) without subtracting CONFIG_ROM_END_OFFSET...
