Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hello,
I am using the ANNA-B112 module with nRF52832 to communicate to an AD5940 AFE using SPI1. I am also communicating with three other sensors using I2C0. This project...
Hi,
We enabled the DFU and sent a new application successfully using the mcumgr command line program, but now we need to do this upgrade process using the host MCU.
...
I am working through an evaluation stage for a new product using nRD52840, possibly updated to nRF54L in the next development phase. The device is based upon Zephyr and being...
I'm getting the warning about CONFIG_BT_CTLR, but I've gone through and changed to HAS_BT_CTLR. I do have the following:
# Maximum Transmission Unit config
CONFIG_BT_GATT_AUTO_UPDATE_MTU...
Hi
I have a nRF52840 setup with external 32 kHz xtal and external 32 MHz xtal, supplied by 3.3V.
I would like the system to be in as low power mode as possible.
Each...
While testing BLE and USB individualy, they seem to work well. When there is simultaneous use, there appear frequent crashes/lock-ups in varius handlers.
BLE used: ble_app_uart...
Hi,
I've got an nRF54L15-DK, and I'm trying to get the sysbuild with mcuboot example working. https://docs.zephyrproject.org/latest/samples/sysbuild/with_mcuboot/README...
Hi,
I would like to repurpose nRFready Smart Remote 3 for nRF52 reference design to use it with the nRF54L15 DK to run BLe channel sounding experiments over this Christmas...
Hi, I am working on Bluetooth of nrf52840 board. I am still learning the SDK and I want to know where can I found the details of error codes, which are considered as 'int...
I need to store just and handful of bytes in flash, some config data. Looking around the forum I've seen recommendation to read and write from/to by using the nvs functionality...
We are in the feasibility stage of a product that requires integration of Apple "Find My" technology only.
Some questions below for pre-development: 1) If we have an existing...
Unable to program external nRF52832 custom board using nRF52840 DK (P19 Debug Out)
I am trying to program an external custom board based on the nRF52832 SoC using the nRF52840...
Hi Team,
1. Radio Firmware upgrade supports only HTTP server?
2. Application can be transferred as a complete file instead of chunks of packets?
Regards,
Sravan...
Hi,
I am attempting to sample multiple channels using the nrfx drivers. Using external timer with PPI over internal timer seemed to provide no benefit so I went for internal...
