Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I am using UART on the Fanstel BLG840F to communicate from the 9160 to the 52840. So far I have successfully been able to communicate from the 52840 to the 9160 but have not...
Here we go again .... I did read many posts in this forum but did not find an answer.
We need to CE test a small Bluetooth HID keyboard for a special use case. Our test...
I am running into the exact same issue described here: https://devzone.nordicsemi.com/f/nordic-q-a/53693/how-to-flash-application-after-dfu-bootloader/217434#217434 Basically...
Hi, Nordic Team
I’m getting started trying to use both MCUboot and NSIB for 2-stage secure boot on nRF9160, and use SEGGER as developed tool. I enable NSIB via “Configue...
Near as I can tell from v1.7 of the product specification, these two parts have the same footprint & pin-out because they're both aQFN packages (as indicated by the "QI")...
Hi Nordic,
NCS v1.8.0
Controller IC 1: Thingy91 - NRF52840
Sensor IC: Laird BT510 - NRF52840
Intro: I currently have 2 devices. A sensor and a controller. For the...
Hi nordic:
NCS1.8.0 , I added UART2 to the NRF9160 LWM2M sample, but it cannot send and receive, but the same code is put into the NRF9160 UDP sample and it can work normally...
Hello Everyone,
I would like to implement a random delay of 10 to 3000ms before my development kit start advertising itself.
I'm using nRF5dk v17.1.0.
How do i go about...
Hi,
I tried to combine the spi and ble_app_uart example. But I got this problem, and the program was stuck in this loop.
Here is what I did:
I am using the 17.1...
Hello all,
we are working on new project that should work for both role (central and peripheral). If I compile the sample "central_and_peripheral_hr for NRF52833DK_NRF52833...
Hi all,
I want to implement a calendar that can be used for many years with nRF52840.
Will leap years be corrected in the nrf5-calendar-example? I looked at the code...
Does anyone have an example of using pinctrl and pwm on a Nordic device using Zephyr for a motor driver or something like that?
All the examples appear to NOT use the pinctrl...
Hi.
Setup:
I use NRF5340. Open project from SES menu "Open nRF Connect SDK project".
nRF Connect SDK Release: 1.4.99-dev1. nRF Connect Toolchain Version: 1.4.0.
Project...
Hello! I tested the ST BLE Sensor sample on my nrf52840 DK. I have a few questions about the source code: 1. Looking at recv(), connected() and disconnected() functions, seems...
