Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
I am building with west and then using this tutorial:
https://docs.zephyrproject.org/2.6.0/samples/subsys/usb/dfu/README.html
to create a .bin file. I then use nrfConnect...
Using NCS 1.8 and NRF5340
Right now I’m able to use the MX25U external flash that we have attached to the nRF5340, We are planning to ship our board with MCUBoot and application...
I am using v7.0.1 S132 SDK on the nRF52832 processor for BlueTooth Light coded in Segger.
I have a high speed output (50uS) to drive an external device using an internal...
My application requires to change the device name as the identification of the device. However, we found the changing the device name might not be detected by the Android...
I successfully used the OpenThread nRF52840 USB dongle support provided by the OpenThread project to implement the radio coprocessor functionality.
However, I had no success...
Hi
I have a strange error in the k_fifo-useage:
Basis is the project peripheral uart
I want to answer on specific commands send via bluetooth
static void bt_receive_cb...
Hi,
I have build the below sample for a nRF52dk-nRF52832 board.
v1.8.0\zephyr\samples\drivers\spi_fujitsu_fram
At compile time I've got this error:
I have followed...
According to Zephyr documentation it is possible to define a thread with K_FOREVER delay so it will not start till k_thread_start is called
https://developer.nordicsemi...
Hi,
i am using a PWM signal to control the brightness of a LED. When the brightness is at zero, i have a random flickering on the LED.
This signal is also present at the...
Hello, i'm using the example ble app uart and I would like to know the maximum data that I cand send to my putty and my phone. Could I have to procedure? I would like to send...
Hi,
I trouble the support team for quite a few months now with NRF5 and I am now trying to get started with the up to date SDK and hopefully being able to get along with...
I have an application using the nRF9160 and its LTE modem to connect to a LWM2M server. During some debugging I enabled LWM2M_LOG_LEVEL_DBG and saw that I consistently got...
Hi,
I recently designed a prototyping board featuring the nRF9160, which we got made for a couple of reasons.
To have multiple boards to test with
Potential to have...
hello
i want to send the data from my 5 of nRF52840DK to 1 of raspberry pi4 , i known the nRF52840dk has built-in bluetooth ble5 and raspberry pi 4 also integrate bluetooth...
