Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear supporters team,
I have a project need to build with a system that includes one central connection to multi peripheral.
do you have any project base similar to my...
Hey all! Today I tested the Asset Tracker App V2 (NCS v1.6.0) with the AWS implementation of the Cat Tracker App.
The rollout was totally fine at the end, and also the App...
Dear Nordic Team and Community!
I want to rise up the question again how to update an advertising message, especially the device name (on nRF52840Dongle, S140, 10059). I...
,i use a nrf52840dk_nrf52840 to run once a nrf5340dk_nrf5340 board's code , I change board name from nrf5340dk_nrf5340_cpuapp to nrf52840dk_nrf52840, change xxx .overlay from...
Hello,
I use central_uart (nrf52840dk) and peripheral_uart (nrf52833dk) examples, NRF Connect SDK v1.6.0
I want to send more than 20 bytes of data,
So, I increase UART_BUF_SIZE...
Hello,
I am using the nrf52840 controller for the development ,i want to read the value from 2 channel of ADC . I just gone through the SDK example code of
SAADC, here...
Hi All,
I was trying to transmit a bare-metal minimal C program to send a raw ADV_SCAN_IND PDU using nrf52840 dev board. Code is listed below:
Here is the linker script...
I'm currently building a device that has the following functionality:
1.) wake from sleep mode and wait 5 seconds for a potential button press
2.) if the button is pressed...
Hello,
I'm trying to debug an issue where a function I wrote that should only be called under a specific condition is calling in an infinite loop whenever the program runs...
Hi, I'm using nRF52805 S112 for my BLE project. I'm using an internal RC ocillator. I would like to ask something about the clock.
1) NRF_SDH_CLOCK_LF_RC_CTIV =16 and NRF_SDH_CLOCK_LF_RC_TEMP_CTIV...
Hello,
I am working on using the open_bootloader with our application and running into a problem.
We are using the GP_REG to jump from our application back to the bootloader...
Hello,
I'm using the following code to loop through the flash memory sequentially and send records created by the flash_fds example:
The data stored in the records...
Hi,
How does numeric comparison works? Shouldn't both devices share parameters in order to display the same number? How can we be protected from MITM?
Thanks!
