Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
We are using over own server that host multiple apis for different functionalities.
I am able to make http post requests to all of them individually and everything works...
Hi
I am about to make an application where a device is sending a sync pulse (60Hz) out to a number of Host's.
when I test with a device and a host, I get approx. 1.22ms...
I am having trouble finding a commercially available BLE 5 dongle that I can be confident will support Linux BlueZ as well as the LE 2M PHY. I would like to know if I can...
Hello,
I have an evaluation board with a nRF52832 chip on it. I added some code to ble_app_uart example and flashed it on the evaluation board.
Here is my problem: I added...
Hi,
I'm trying to use BLE to send data to a computer from the NRF52840 DK. So far I'm trying to get nrf_sdh_enable_request() to compile without errors, but I keep getting...
Hello,
I have both an installation of NCS v1.5.0 from Toolchain Manager (TM) and from the Getting Started Assistant (GSA) on Macbook running macOS High Sierra. The TM SDK...
Hi
I am using nRF9160DK board and need transmit gps data to web site, I am trying with udp but have problems with that, I would like to know what protocol use asset_tracker...
Hello,
at the moment I am trying to implement a counter that increments every 1ms. I wrote the following code for this:
Regarding to the documentation ( https://infocenter...
Hi there,
I am running a custom board based on the nRF5340-DK. It's a minimal board, notably with both oscillators
It seems to behave itself with low-rate BLE use-cases...
Hi.
I'm having trouble flashing my Thingy:91 with the nRF9160DK as a debug probe.
The DK is set to 1.8V, I have a 10pin JTAG cable connected to the debug out of the DK...
What is the UICR setting in nrf51822,S110? Currently, when I develop with nrf51822,S110, the UICR area is 0xFF. I want to set the UICR as follows, is there any way to set...
Hi,
I am using multiple channels of SAADC for monitoring some data and then I send every 20 samples of adc in a 32 packet through Radio/BLE using the esb_ptx example and...
Hi All,
I am a beginner to nRF52 and Nordic Microcontroller, I want to understand the flow of code and its BLE sequences in detail . I am also not proficient in the C language...
