We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
The only way I can see to do it is by two separate PPI calls. So Timer1 "tasker" is firing both the capture and clear... but will they execute sequentially?
Hi,
I just bought the NRF52850 DK. Currently I do not have the JLink connector to perform debugging using UART.
Is there is a way I can print printf or NRF LOG through...
Hello expert,
I would like to design a custom PCB that has two transceivers on it. One transceiver is working as a beacon/continuous wave generator (TX) and the other one...
On the basis of NRF24L01 +, an antenna was designed. after designing, I need to carry out the coordination of circuits. Do not tell me how best to do this, what values to...
I had a setup where I could DFU OTA a NRF52832 based board
I moved to a NRF52840 based board and now during the OTA DFU I get messages like this
I did try a new bootloader...
Hello, guys.
We have nRF9160DK and nRF Connect SDK v1.3.0. The version of the LTE modem firmware is the latest (v.1.2.0).
In our design, we are able to initially connect...
Hi Nordic team,
I just purchased a row of new nrf9160 SiPs for our IoT products. We are testing with new made cuicuits.
We use the same circuit schematic that worked with...
Hello,
Problem: BLE doesn't work on a OurBoard with nRF52840 (Schema1).
1) BLE example is working DevBoard (can see BLE server by scanner). On the OurBoard the examle...
Hello,
I've been testing HCI_UART from Zephyr RTOS on nRF52840DK and own device which has nRF52840 + FT232R as USB-UART converter. Regarding the own device it's a circuit...
I am studying the beacon example provided in the SDK (The project is found in following directory C:\Nordic_semi\nRF5SDK160098a08e2\examples\ble_peripheral\ble_app_beacon...
Hello there, I'm developing a device who will use two NRF52832(ANNA-B112 Module). They will communicate as central and peripheral. But i'm facing a problem, i need to after...
I could decrease current consumption at v1.2.0, but couldn't at 1.3.0. 520uA flows in k_cpu_idle();
How can you do that?
Also, in v1.3.0, CONFIG_UART_0_NRF_UARTE is depricated...
Hello
Good day!
Problem: We have got a new nrf52DK, and in our application development we use GPIO interrupts (we have set up 4 gpio interrupts). Surprisingly the GPIO...
