Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
We are using a nRF9160 and are interfaced to a Texas Instruments AM335x running Linux over a UART interface. I've read through the guide on making a custom overlay. So far...
Now I am working on ble_app_uart project. For security reason, I don't want any unaccepted mobile phone connecting to my peripheral device.
From this post link text ,
...
Hello
I am working on mpu6050 sensor in sdk v14. I succeeded in obtaining the acceleration value of this. I'm trying to get the angle of the sensor using this value.
I...
Hello Nordic Support,
I am developing an application which has BLE bootloader and application using the custom nRF52840 board and nRF5 SDK v17.0.0. Both of them require...
Hello. I'm working on sdk v17 and I'm trying to control the LEDs in order using a timer. Before using the timer, we made it easy using delays. Apps work when they receive...
Is it possible to sniff the data between two device that already connected if yes then how if no why?. What are other method for sniffing oob and passkey security based devices...
I have moved my project over to SDK 17.0. So far I have changed very little.
On compiling I straight away get a liner error: "Undefined reference to '__RAM1_segment_end__...
Hi to everyone:
As the title suggest I'm using the NRF52840 PCA10059 dongle and everything works as expected.
The issue comes that I've modified the dongle to instead...
Hello,
We have developed a new type of smartphone gamepad using the nRF52832 chip. But for some reason, it works for some games and not for others. And only partially work...
Hi,
I have problem with using nrf_serial.h, I am receiving data from Ublox GPS, baud rate = 9600, no flow control as we dont have enough IO pins.
Device is nrf52840 with...
Hello, I'm trying to integrate an SPI slave into ble_app_beacon example. Power consumption of ble_app_beacon between advertising is up to 10 uA. But if I write a byte over...
Hello
I am modifying the example of mpu6050 of sdk v14 in sdk v17.
After build, it is printed that there is no path to the file as shown in the image below.
(The...
Hello We recently went to a test facility SGS, in San Diego, with our nrf9160 device trying to get a pre-cert scanning completed to find out if there are changes needed before...
Using SDK 15.3 and S132.
I'm having similar behavior to the thread below:
https://devzone.nordicsemi.com/f/nordic-q-a/12066/gap-disconnect-stops-app-timer
After disconnecting...
hi ...
how to update the advertisement packet .. I have seen many post regarding this ,I am not getting clear , anyone can share me the piece of code which will help me
