Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
If I use a breakaway for some debug pads which SWDIO and SWDCLK are connected to and then snap it off so the traces are no longer connected to anything, will this cause a...
I'm trying to run the https://github.com/NordicPlayground/nRF52-ble-long-range-demo on Fanstel modules with integrated AFE by Skyworks - BT840X(E) https://www.fanstel.com...
I'm trying to connect to an AWS MQTT broker I have set up based on the code in https://github.com/joakimtoe/fw-nrfconnect-nrf/tree/36532a8ca60bf7139a988b5cbb4e6cb47948a9fa...
Hello In this thread we discussed a possability of building a system with large number of conecctions. So, we need to get data from 30 peripheral nodes on one central host...
Hi,
I'm developing a product that should take an image of a low-resolution image sensor, process it and send the result via BLE.
The camera has an 8-bit parallel interface...
Hello, I was finally able to connect the board via LTE to my nRFCloud account. However, when I go through the getting started guide, specifically the programming a sample...
Hi
Now I use the SDK15.2+MESH3.10 build my project.
Because my firmware was very large.
Moreover I want to use the nRF Connect update my device.
So,how to integrating...
HI I started off to test all the drivers before the actual development process kickstarts.I tried using the TWI sensor example for an i2c driver check.I used a DS1307 simple...
Hi,
I'm trying to add an interrupt triggered event to my code (which is based on the experimental LPN example from the Mesh SDK).
Looking through the development zone...
Hello , I come from taiwan.
I am using ble_app_hrs_c to connect my heart rate watch
I can set m_target_periph_name to search for devices with the same name and connect...
Hi, I'm developing a project on nRF52832 with LIS3DH accelerometer . Is there anyone here who has already done a similar project using the nordic SPI bus (not TWI)? Please...
Hello NordicSemi,
Actually we want to develop a product that can communicate with the iPhone over USB (lightening connector).
Basically want to implement iAP2 protocol...
Hello,
While i am debugging application in SES.I got the error like "stopped by vector catch"
How it relates to hardfault handler .Why it is happening
Kindly provide...
Hello everyone at Nordic!
The QFP version of the nRF52 has a reference PCB design layout, which is shown on the eval board. For example, if you look at the schematic for...
Hi,
I am using Segger Jlink with SWD interface
nrfjprog used to work perfectly fine for me but, suddenly, I cannot run any nrfjprog commands, I get the error JLinkARM...
