I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi
I have a problem changing the max_rx_octets and max_tx_octets parameters with the sd_ble_gap_data_length_update function. On request from the app the size is attempted...
HI, we have updated our DK firmware (mfwnb1nrf9160030123prealpha) for nb-iot but after inserting the Vodafone (Ireland) V-Sim we only have a flashing LED 3.
nRF connect...
Hi all
Chapter 26.1.1 of the nRF51 series reference manual v3.0 states that the pins used by the SPI master have to be configured in the GPIO registers according to table...
Hi, I am interested to learn THINGY 52 working
I want to know how does the Thingy52 works?. any tutorial to explain the function of THINGY52
How to delete the boot loader...
Hi
The example in SDK15.2 for 52840 as a Beacon is not long range (I think).
Is there another example that will enable long range and also to enable connection?
While...
Hello,
I'm use laird BL651 with nRF52810 module. I flash the chip with beacon program from zephyr samples. I use Segger Studio.
The chip is discovered by smartphone (with...
Hi,
is it possible to scan 10000 beacon having adv interval of 10 seconds. is their any maths or formul we can do ?
i have set nrf52 to scan continuesly,
Hi,
There have 4 PWM sample code (low_power_pwm, pwm_driver, pwm_library and pwr_mgmt) in SDK 15.2.
I my use case is "Control 6 PWM output with different duty-cycle and...
We have written an application based on SDK V12.2.0 using S132_V3.1.0 for the nRF52832 and have been dealing with an issue where the module constantly enters a hardfault....
Let's suppose the PC (a laptop) goes to standby while a BLE connection is established with a Nordic dongle using pc-ble-driver v4.0.0:
- With SD API V2, status handler is...
Hi
I downloaded and successfully build and ran the asset tracker sample on the nRF9160 DK using segger embedded studio. In a first step I want to reroute the debug UART...
Hi there,
I have a project where I am using the NRFX I2S Driver. I am using SDK 15.3.0 and SES 14.2.
In my sdk_config.h, I have the legacy I2S driver disabled and the...
Hi all,
I read from previous answered question found that version6.1.0 with s15.2 supported only S=8 encoding transmision when LE_CODED_PHY is chosen.
Does nRF52840 with...
Hi,
HW: PCA10056
SW: nRF5_SDK_15.2.0_9412b96
I try to enable CRYTO feature in my module. But undefined reference to `CRYS_ECPKI_GetEcDomain' and other undefined reference...
I'm migrating a project from SDK 14.2.0 to SDK 15.3.0 and using the UART (not the UARTE). I want to use the legacy UART driver. I'm hitting these errors when compiling
app_uart_fifo...
