Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
I want to use the CUSTOMER[] fields for their apparent intended purpose of storing calibration data in nonvolatile memory. I find it quite absurd that the softdevice would...
Hi,
I am using PWM to control LED power.
The code i use for initializing the PWM is-
app_pwm_config_t pwm1_cfg = APP_PWM_DEFAULT_CONFIG_2CH(1000L, PIN1, PIN2); err_code...
Hello,
I am trying to run the example DFU over TFTP. I have setup a tftp server with following configurations:
# /etc/default/tftpd-hpa TFTP_USERNAME="tftp" TFTP_DIRECTORY...
Hi,
I've followed the link https://devzone.nordicsemi.com/f/nordic-q-a/35675/how-to-use-static-passkey-for-a-no-display-no-output-peripheral
and added it to uart example...
Hi,
My app requests a timeslot in various conditions - sometimes the timeslot needed is long, sometimes short (unknown a priory) so it asks for the longest possible...
Hi,
Is there any easier way when using Eclipse IDE with GCC for nRF5 SDK 15.2 development to get the Include files in the examples to be recognized easier than tediously...
My set up contains beagle bone black as Application board. PCA10001 board with S120 Softdevice using nordic_sdk_10 running ble_connectivity example program.
I initiated...
I have a Teledyne protocol analyzer for capturing over the air data between an nRF52840-DK and an iPhone 8 device. How do I obtain the encryption key from the nRF52840 SoC...
Hi,
I want to verify Bluetooth on my board is good or bad.
Note that, I do not have any spectrum analyzer or vector network analyzer, just development kit.
I found example...
On the product page the nRF52810 is mentioned as supporting ANT. https://www.nordicsemi.com/eng/Products/nRF52810
However in the info-center looking at the compatibility...
Apologies if this is a Segger question vs a Nordic question.
I have already been evaluating SES for a non-Nordic project, and so it's already installed [on Mac].
I am...
Hello Nordic,
I have already used an earlier version of nrfconnect on this lcomputer( windows 10 language PT-BR).
After upgrading to 2.6.1 I got the the error below: ...
Zboss som times gets stuck in loop trying to start network steering when running sample, most of the time it eventually makes it out of the loop
but what causes the failure...
Hi,
I am using nrf51822 to get DS18B20's temperature data, but I am fail to do it.
Would you please give me an sample C source code which can get temperature data from...
in nRF5_SDK_14.2.0_17b948a project, we get sensor x y z w data in a loop process, the data which print in uart shows very smoothly.
but if i push buttons many times in a...
