Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
hi...........
i am using nrf52832 and a peripheral device . i have merged two programs uart and twi sensor . i am getting the data everything is fine , but after the few...
Using Rigado board, MBD350, I am able to write and test basic application using UART and BLE
using my custome board I get the following error:
NRF_BREAKPOINT_COND; ...
Hi.
I development nRF52832(SDK15.00.00, S132).
I have modified SDK15->examples->ble_peripheral->ble_app_uart->pca10040->s132
I want to unuse uart, So I using app_uart_close...
Hi Sir,
We would like to use 32-bit address flash (MX25L25635F), and we set the " QSPI_CONFIG_ADDRMODE" to "1" to support 32-bit address.
when USB port connect to PC,...
i use the BLE uart example in SDK11.0 to test. I delete the UART hardware init and just use the BLE send data to phone every 500ms. I found whatever i set the MIN_CONN_INTERVAL...
Hi,
I have an issue with a situation where a client remains connected when not needed anymore, I need to terminate any connection that has been active too long, for example...
Hello,
I used the gzll_host_ack_payload_nrf24le project and gzll_device_nrf24le to test the communiction between two nrf24les over Gazell. The result is that the host could...
Hi,
We would like to add another element to the provisioner. Is there an example how to provision and configure a client element on a provisioner node using the new SDK...
Hi, if the setting of the nrf52832 is shown as below:
Is this possible to happen?
cause when I was trying to use the power profiling example to test the connection mode...
Hello,
the current situation is nrf52832 can not receive the ack payload from nrf24le.
nrf52832 is DEVICE ,using the project from nrf5_sdk13.0.0\exzmples\multiprotocol...
Hello.
I need to compile the bootloader for the nRF51822 chip, using the the nRF SDK version 6.1, and ARM GCC.
I do not have access to Keil.
How can I achieve this?...
I'm using an old version of the nRF5 SDK (v11.0.0, SoftDevice v2) as supported by the SparkFun nRF52832 breakout board and the Arduino BLEPeripheral library.
Having set...
I am using nrf52 DK and sdk 15.0.
I want to know whether we can transfer the file over the BLE or not?
I am using ble_app_uart example,Is there any possibility to modify...
