We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
using the sample code at
invent.module143.com/.../
i am able to use nrf24l01 to communicate raspberry pi with arduino, but the problem is the timing. I found it takes...
Did anyone attempt time of flight measurements with the nrf52 yet? I'm looking into this as a possibility to measure distances. I was thinking that using the 64 MHz clock...
I AM GENERATING A PWM EXTERNALLY (OUTPUT FROM A WATER SENSOR) AND FEED IT TO A NRF51422 BOARD. I WANT TO COUNT THE PULSE COUNT(LOW TO HIGH TRANSITIONS ONLY). CAN I DO IT WITH...
How to configure an app_timer in counter mode. i just want to count number of pulses in pwm using app_timer. i didnt find any example in which app_timer used in counter m...
I'm trying to use fstorage module for event logging; several pages are used as a large circular buffer. When logging wraps from one page to another, the new page needs to...
Hello every!
I was developed my aplication base on nrf52 SDK (version 14.0). I am confused about SDK_config.h file. I can't cognize which macro should be 0 or 1. Example...
Hi all,
we are using the Nordic Uart Service in our product and Id like to connect our hardware to a Linux powered PC. Does anyone know how much effort it would be to make...
Hi all,
I have a working ADC implementation (S130 + Application) and use it to measure an analog input continuously.
However if I use the same code on top of bootloader...
When I have a test using nRF24l01+ with STM32, I can only get a playload datarate no more than 450kbps using nRF24l01+ 2M mode.
How can increase the playload data rate and...
I have been using two NRF24L01 to communicate with each other using just simple Arduino Uno Board.
it worked for 5 days and now all of a sudden it is now working.
I tried...
Hi,
in order to add flash programming support to the iSYSTEM toolchain based on a
customer request I would need a flash reference driver/monitor implementation.
Would...
The sync time for my nrf2460 seems to be about 4 seconds. Is this normal? Secondly, once
the pair is synced at close distance, one or two feet, as I move away sync is lost...
I'm planning on having all of the different Device Information Service characteristics (fw_revision, sw_revision etc) with each being just a single integer for version number...
Can someone tell me what these errors actually mean
JLinkARM.dll CORESIGHT_WriteAPDPReg returned error -1.
JLinkARM.dll CORESIGHT_WriteAPDPReg returned error -102.
...
