Hello Team,
Could you please share some sample application or procedure to handle power modes (Sleep, Deep Sleep, etc) of the nrf9160.
Please let me know.
Regards, ...
Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
NRF52820
PAN1781 EV Board
Segger Embedded Studio 5.62
nRF5_SDK_17.1.0_ddde560
S140
Hello,
I'm currently working on an indoor positioning system and as the title...
Hi,
I compiled an application that should start at address 0x40000. However, executing an OTA DFU always places the application at 0x26000, right after the softdevice. ...
In a previous ticket on another topic this question came up. Given it was a tangent to the original topic of that thread, and I think it would be helpful to others, I decided...
Hello,
I have a battery with 4.2v max charge. Since this is outside the input range for nrf52832, I have to add a down voltage regulator. Now the question is: Should I...
Hi!
I need to modify the code of the secure and the non-secure images of my project.
I tried to follow this guide https://devzone.nordicsemi.com/guides/nrf-connect-sdk...
Hi
I have a project which is using 53832 as the master , main 52832 works with smart phone by bluetooth ,and broadcasts ebike information throght the ANT+ .
I would...
Hello everyone
I have a bunch of custom dongles from the company I work for and two of them started to behave in a strange way after I tried to erase and program them through...
Hi,
I'm currently in the evaluation phase of a project and would like to use a NRF52 chip, but I need to ensure, that I can use two independet hardware timers. I had already...
I am running a PWM pin on 15 using this DT Overlay:
pwmnmos {
compatible = "pwm-leds" ;
status = "okay" ;
pwm_nmos0: pwm_nmos_0 {
pwms = <& pwm2 15 >;
};
...
Hello,
I built my application based on your "ble_peripheral_lbs_coex" example. Board is nRF5340DK.
Mesh and BLE (NUS service) run together but I noticed that the NUS UUID...
I'm using SDK 17.1.0, softdevice 7.2.0 as a Bluetooth peripheral. I'm sending notifications to a paired iPhone. The notifications are keyboard keys, and so are time sensitive...
Hello,
I am trying to figure out how to save a small number of counters to local non-volatile memory on the nRF9160. I have a few questions.
1) How do I determine whether...
Hi
I want to measure chip temperature of nrf52840.
For this I referred " sdk-zephyr / samples / bluetooth / peripheral_ht / src /hts.c"
and I have enabled "CONFIG_TEMP_NRF5...
We are using nRF9160 DK (SDK 1.9.1) with "serial lte modem" firmware. We are trying to test downloading files from a server using AT commands to work with HTTP. The file is...
Upto a week I had *no* problem in programming a nRF52840 dongle with an app I am porting from the nRF52840dk.
All of a sudden I can't get the app running, the dongle appears...
