Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi, I'm working with nRF52832 DK, SDK 15 on Windows with Keil5. I create Multiperiherial Nus with peer manager and fstorage and it works, but after some connetions I get an...
<error> app: ERROR 8 [NRF_ERROR_INVALID_STATE] at the same line as
ret_code = ble_advertising_advdata_update(&m_advertising, &new_data, true); APP_ERROR_CHECK(ret_code);...
Hi, maybe it's time for my dream project to come true. I have one NRF52840 DK on the table, one desktop PC, one laptop (BT 5), one iPhone X (not mine, just for a case) and...
Hey,
I am new to this , i am using nrf51822 for development , as the documentation says i downloaded the sdk and i got the nrf5 dk and i am using the Segger embedded studio...
Having problems with nrfjprog and a custom board. I connected my custom board to the NDK via P20 and flashed a program to it. The program was a variant of the pwm_library...
dear
i am using this project as slave
\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\
this project as central
\nRF5_SDK_14.2.0_17b948a\examples\ble_central...
Hello all,
Almost giving up, I'm struggling to make my nRF9160 working. I can't use the LTE Monitor at all!
Tried everything, I think, and run out of ideas. All AT commands...
I have a custom board with nrf52840 with cr2477 battery (1Ah capacity). I was download firmware to board and after a week the battery voltage dropped to critical. In the firmware...
Hello everyone.
There have a scenario, nrf52832 starts a direct advertising , but the dest ble device is not bonded(it could be any other central device), when the dest...
Hi. I am developing the nRF52832 using the NRFX module of the SDK version 15.2.0. We convert the UART signal to RS485 and communicate with RS485 to the outside. RS485 communication...
Hi,
I'm using nRF52832 on a custom board and I have tried to run sdk example nfc_url_record, but it doesn't work.
I have tried to find solution among existing answers...
Hi All,
For my project I'm using NRF52832 IC and NRFsdk. I need 2 GPIO external interrupt to get notified. I'm able to configure both pins and able to see the trigger when...
Hello Dev-Community, I have modified the Thingy Firmware for a custom made board which has also the MPU9250 with TWI connected. Everything works fine, if i use RTT Viewer...
Hi,
Referring to this thread -
If the saadc sampling is trigger by a timer (through ppi), what is the correct way to saadc_uninit() without using the global m_sampling...
Hello,
nRF52832 datasheet denotes saadc sampling time in scan mode (paragraph 37.5.4) as:
What is extra time it takes for the easyDMA to store the samples in RAM ? ...
