Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
As the question explained. I want to know if we can implement all three zigbee roles viz, Edge, Router and Co-Ordinator in a single project and can be able to switch them...
Dear Nordic Team,
We are working on a solution where we want to only connect to a certain device if it is a known device and not accept any random requests.
We believe...
Hi ,Nordic
nrfx_err_t nrfx_pdm_buffer_set(int16_t * buffer, uint16_t buffer_length)
I wonder the buffer is PDM buffer or PCM buffer ?
also want to know that how...
Dear support team, The customer used ncs2.6.0 to run on nRF52840 to make matter over thread smart door lock. When stress testing the switch lock (repeat: password unlock ...
I 'm using zephyr to create a custom nrf52832 board .
I 'm using the Devicetree Visual Editor .
Any idea why I can 't select this specific display controller ?
The datasheet...
Hello, As for my peripheral BLE NUS service under NCS 1.9.2, when I search and connect it from my Windows PC running nRF Connect for Desktop BLE Standalone 4.0.0, I found...
I am sending data from iOS to a nRF5340DK. I have some code showing the TX/RX MTU Size:
Which shows: Updated MTU: TX: 527 RX: 498 bytes
But on the iOS/Controller...
Hello!
As stated in the subject, when I followed the steps in the chapter of running OTBR using Docker ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols...
Hi, am using the nrf52dk with nrf52832, nrf coonect sdk 2.5.1/ toolchain 2.5.2 and am building a prototype to aquire the signal from the ckp and cmp sensor in the car when...
Greetings,
We switched from nrf9160 to nrf9161 and got the first boards manufactured. NRF9160 has been working fine but we wanted improved GNSS functionality on board. ...
Hi all,
I have plenty of experience with the Old SDK, IAR/Keil/SES, nRF51, nRF52, Soft Device, etc. However, I'm new to the nRF Connect SDK, VS Code and nRF5340. I've successfully...
Please let us know which PINs of nrf5340 are used by BLE stack and which pins are used by peripherals like UART0 and UART1? We are converting our code from nrf connect V 1...
Hello,
We are evaluating MCU's for a low cost Central device that is extremely cost constrained. The nRF52805 and the nRF52810 both have the same RAM (24 KB) and FLASH ...
Hello,
I'm stuck in the nRF Connect SDK Fundamentals course on lesson 3, exercise 1. When opening the COM port to view the printk messages, I get an error when connecting...
Hi,
I am working with nRF5340 and nRF Connect v2.7.0. When I try the mass sample it works fine. When I take the code to my custom project, I have
ff.h no such file or...
