Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Good morning,
Today for a Brazilian Logistic company, I am developing a Embedded System for Low-power tracking and other features, with a nRF52840 in a RAKWireless solution...
i have developed the VL53L5CX code with BLE nrf52840 and it is working fine but issue i have faced is the USB port Restarted Whenever Firmware Download Process Start below...
HI Nordic support team.
I have a question relate to TX power in ANT application:
- ANT Tx application using: ant_broadcast ->Tx
- ANT Rx application using: ant_continuous_scanning_controller...
I've been running a Central + Peripheral application. I can successfully scan for devices and get the advertising data.
However, when I try to connect, the code seems to...
I am running the Direction Finding Connectionless Beacon sample using my nRF52833DK to transmit CTE packets. I am using the u-Blox ANT-B10 antenna board to receive the CTE...
"I am using ncs v2.6.1 on VSCODE, and the following issues have occurred:
Issues:
- Existing build files are not visible in the application.
- New builds are possible...
The multicell loaction has been working fine for a long time. About 8 days ago, I started to receive an error when requesting the location through "Here"
Any help would...
I am working on an application for an LE Audio Broadcast sink on an nrf5340 Audio DK. I am using code from the nrf5340 Audio application (v2.6.0) for the le audio parts. I...
Hi! I'm new to using the Nordic products and I wanted to be able to power my Thingy 91 device without the use if the USB and with a separate external power supply. On the...
Hi there,
Currently we are developing our own system to drive WS2812B LED's using the NRFX pwm library. And the coloring and signaling works fine when it is in a bare metal...
Hi,
I am using nrf52840 and SDK17.1.0.
I need to calculate CRC16 for communication with an another module. I found that we have an API for that. I would like to know what...
We are planning to develop an Matter door lock which includes NFC/RFID, Audio, keypad and BLE functionalities used separately. I am considering using either the nRF52840 or...
I tried setting the VDD voltage in the 9161 DK to 3,3 V, but it remains at ~1,76 V.
I'm able to enable/disable the GPIO extender just fine, so at least reading & writing...
I have had great success developing a project based on the peripheral_uart sample. Now I am trying to add DFU over UART to that project. Specifically, I would like to add...
Hi,
I have the following minimal example:
main.c
proj.conf:
Now, when setting CONFIG_SERIAL=n my nRF52840DK drains about 3-4 µA, when setting CONFIG_SERIAL=y it...
